Omega Owners Forum

Chat Area => General Car Chat => Topic started by: TheBoy on 16 September 2013, 13:40:43

Title: ABS fault - why heavy steering?
Post by: TheBoy on 16 September 2013, 13:40:43
Never really thought of this, until she started moaning about it, and she's right...

V6 servotronic, uses speed signal to reduce assistance as you get faster.

So why is it, when speed signal disappears, due to intermittent ABS ECU, does the steering go heavy? Surely it should be as light as anything, as it assumes you're not moving, thus need maximum assistance?
Title: Re: ABS fault - why heavy steering?
Post by: Entwood on 16 September 2013, 14:01:57
Never really thought of this, until she started moaning about it, and she's right...

V6 servotronic, uses speed signal to reduce assistance as you get faster.

So why is it, when speed signal disappears, due to intermittent ABS ECU, does the steering go heavy? Surely it should be as light as anything, as it assumes you're not moving, thus need maximum assistance?

Opposite I thought.. goes to mimimum assistance as it "assumes" you may be do some much faster speeds and too much assistance would be dangerous .. so in the name of safety, no signal = no assistance
Title: Re: ABS fault - why heavy steering?
Post by: Andy B on 16 September 2013, 14:12:31
Never really thought of this, until she started moaning about it, and she's right...

V6 servotronic, uses speed signal to reduce assistance as you get faster.

So why is it, when speed signal disappears, due to intermittent ABS ECU, does the steering go heavy? Surely it should be as light as anything, as it assumes you're not moving, thus need maximum assistance?

Opposite I thought.. goes to mimimum assistance as it "assumes" you may be do some much faster speeds and too much assistance would be dangerous .. so in the name of safety, no signal = no assistance

Sounds a reasonable assumption to me  :y  :y  :y

I remember taking my 2.2 Carlton onto the motorway for the first time, I'd never had power steering before, & this was the usual basic always on type of assistance. It felt like I only needed to look hard at the wheel & it'd move!  ???
Title: Re: ABS fault - why heavy steering?
Post by: Kevin Wood on 16 September 2013, 14:40:01
Yes, I'd guess it "fails safe" to minimum assistance by design too.
Title: Re: ABS fault - why heavy steering?
Post by: TheBoy on 16 September 2013, 17:08:55
I understand the failsafe argument, but how does the servotronic ECU know. AFAIK, it only receives speed signal, nought else. So it will just assume standstill?
Title: Re: ABS fault - why heavy steering?
Post by: TheBoy on 16 September 2013, 17:09:26
Can you tell I was laying awke last night, pondering this one ;D
Title: Re: ABS fault - why heavy steering?
Post by: aaronjb on 16 September 2013, 17:20:01
I understand the failsafe argument, but how does the servotronic ECU know. AFAIK, it only receives speed signal, nought else. So it will just assume standstill?

Does it receive RPM by any chance, as well? I know the Corsa electric PAS system does, for that reason..
Title: Re: ABS fault - why heavy steering?
Post by: Kevin Wood on 16 September 2013, 17:21:22
IIRC, the steering goes heavy after the ABS ECU has actually failed while the vehicle is moving or if it wasn't there (or working) at startup. I guess the servotronic box looks for activity at startup of the ABS ECU, and invalid activity such as coming to an impossibly sudden halt from <mumble> MPH, and, if it sees this, goes into a fail-safe mode.

There's also the possibly that it it's simply that the signal is normally in one state when the car is stopped, but, with a failed ECU, it reverts to the opposite state.

The servotronic box raises a code if it detects a faulty speed signal input, so there must be some intelligence in it. Granted, it only has the speed signal as an input so it can't compare it to anything else to determine if the car is likely to be moving.
Title: Re: ABS fault - why heavy steering?
Post by: TheBoy on 16 September 2013, 17:30:56
IIRC, the steering goes heavy after the ABS ECU has actually failed while the vehicle is moving or if it wasn't there (or working) at startup. I guess the servotronic box looks for activity at startup of the ABS ECU, and invalid activity such as coming to an impossibly sudden halt from <mumble> MPH, and, if it sees this, goes into a fail-safe mode.
That was my feeling. But, whilst pondering it, surely it wouldn't go to failsafe in a 100% brake locked up stop, as I bet they are the same config for ABS and non ABS models.

I'd check for servotronic codes, and see what configs it has on, if only I had the facilities  :'(


Moving to car chat, as its not a help request (as we all know what the cure is), more of a discussion point :)
Title: Re: ABS fault - why heavy steering?
Post by: Kevin Wood on 18 September 2013, 10:00:47
I'd check for servotronic codes, and see what configs it has on, if only I had the facilities  :'(


I can bring the Tech 2 to Serek's on Sunday (if I make it). Alternatively, I'll be passing your way in a couple of weeks anyway. :y