Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: danzigfan on 02 June 2015, 17:06:11
-
Hi guys, a question about rocker covers for a v6 ... :-[
Rocker covers from 2.6 will fit on 2.5 but plug leads will have excessive play due to holes made for dis pack. Would it be ok to fit those on 2.5 or not?
And another one, if breather system is cleaned regurarly....(I know :-X)...could I fit alloy rocker covers from 2.6 vectra?
Thanks in advance guys
-
They still leaking :( Vectra covers will fit but as said breathers need checked more often . It does seem to me that the rocker covers on the earlier models seem to warp more than the newer ones .. could never get mine to seal properly on the pf no matter how hard i tried :(
-
Yes I know the feeling >:( The "groove"(I hope this is the expression) where the gasket goes on cam cover isn't straight anymore. It's all wobbly and I'm not surprised it leaks though it's not that bad now (after refiting gasket for five times >:( :-X)
Paying arround 300eur for set of plastic cam covers with gasket set is a bit painfull, getting used plastic cam covers is risky (can't buy any of yours couse I ditched my credit card - using only maestro now) so the only way to go is alloy cam covers for me :-[ and even those are rare here in the land of renault dci nation :-X
-
Yes I know the feeling >:( The "groove"(I hope this is the expression) where the gasket goes on cam cover isn't straight anymore. It's all wobbly and I'm not surprised it leaks though it's not that bad now (after refiting gasket for five times >:( :-X)
Paying arround 300eur for set of plastic cam covers with gasket set is a bit painfull, getting used plastic cam covers is risky (can't buy any of yours couse I ditched my credit card - using only maestro now) so the only way to go is alloy cam covers for me :-[ and even those are rare here in the land of renault dci nation :-X
Must have done mine 10 times or more and changed the covers , still leaked . I was considering the metal covers but then i sold the car ::)
-
2.6 Vectra doesn't have metal covers... Also plug leads should be a secure fit to the plugs regardless :y
-
(http://i1103.photobucket.com/albums/g480/danzigfan1/Omega%20wax/_1.jpg) (http://s1103.photobucket.com/user/danzigfan1/media/Omega%20wax/_1.jpg.html)
Upper photo is reason why I'm asking Al, that seem as metal covers with holes for dis pack
-
(http://i1103.photobucket.com/albums/g480/danzigfan1/Omega%20wax/_1.jpg) (http://s1103.photobucket.com/user/danzigfan1/media/Omega%20wax/_1.jpg.html)
Upper photo is reason why I'm asking Al, that seem as metal covers with holes for dis pack
Interesting.. .The 3.2 in Vec C uses same covers as Omega... Presumed 2.6 was the same :-[
Ignoring the whole metal covers point, 2.6/3.2 covers will be fine and dandy :y
-
Good to hear :y I found a 2.6 veccy engine for 300eur just need to ask if it has metal covers and "IF" I could get those alone of the engine. Don't need another lump in the garage :P Thanks for help guys
-
And I found two sets of low mileage plastic cam covers :D an hour ago, Going to check those after work today. 50eur for two pairs :y
-
2.6 Vectra doesn't have metal covers... Also plug leads should be a secure fit to the plugs regardless :y
As pointed out, it does. All the Vectra B V6's are metal covers. 2.6 have COP recesses, 2.5 don't.
The Signum 3.2 and the Vec C 3.2 both use plastic covers.
It's a pitty you can't buy on here I have more than one set laying around.