Omega Owners Forum
Chat Area => General Discussion Area => Topic started by: Nick W on 04 January 2017, 19:07:39
-
Clean and regrease the bearings on the wheels, and we're changing the brake discs, so remove old ones.
OK
So after doing the bearings on the first wheel, I started on the 9 nuts and bolts retaining the disc. Which got harder the more I undid, and the last bolts didn't fall out.
Then there was a loud bang, and something hit me in the face.
Some utter oppswit had forgotton to let the bloody tyre down :o :o :o :o
So that's five bent bolts at a tenner each, and a very scary moment.
-
Could have been worse... might have been an angle grinder :D
-
Clean and regrease the bearings on the wheels, and we're changing the brake discs, so remove old ones.
OK
So after doing the bearings on the first wheel, I started on the 9 nuts and bolts retaining the disc. Which got harder the more I undid, and the last bolts didn't fall out.
Then there was a loud bang, and something hit me in the face.
Some utter oppswit had forgotton to let the bloody tyre down :o :o :o :o
So that's five bent bolts at a tenner each, and a very scary moment.
I've read this through 5 times and I still cannot guess what letting the tyre down has to do with removing a brake disc :-\ or why there are 9 nuts & bolts :-\
I imagine you will give us more details when the swelling subsides.......
In all seriousness it sounds like you had a close shave there & I hope you didn't take too big a kit.
-
A lorry wheel perhaps? :-\ :-\ :-\
-
Nah, be aircraft related, disc mounted to the hub of a two piece wheel at a guess...
Hopefully nothing too drastic/painful ;)
-
Five wheel bolts and four holding disc? ??? :-\
-
Five wheel bolts and four holding disc? ??? :-\
All nine through at least three pieces of metal perhaps :-\
Summat like this:
http://www.kitplanes.com/issues/31_6/shop_talk/maintenance_matters_june_2014_21016-1.html ;)
-
Oh, i see, i lead a sheltered life you know. ;D
-
It's off a big Cessna.
The wheel is in three pieces, inner and outer like you would expect, plus a central spacer for the inner tube to push against; all clamped together by nine nuts and bolts that also hold the brake disc. I had the tyre between my knees, and got four of the bolts out before the pressure started pushing the assembly apart, jamming the remaining ones in place. The eighth nut was what hit me in the face, and the five stuck bolts were bent about thirty degrees. They're high-quality 3/8", which should give some idea of the force involved. I had to use a cut-off wheel to get them out.
It could have been very painful. And expensive.
-
Sounds like you had a very lucky escape. :o
-
That you are okay is the main thing. Much easier to replace mechanical parts than human bits. ::) ::) ::)
-
Is there not a recommended procedure involving decompression before dismantling? Having worked on and in both fighter and large transport aircraft for 40 odd years, this was invariably the case. But perhaps for light aircraft there is no set procedure in this instance. :-\ :-\ :-\
-
Is there not a recommended procedure involving decompression before dismantling? Having worked on and in both fighter and large transport aircraft for 40 odd years, this was invariably the case. But perhaps for light aircraft there is no set procedure in this instance. :-\ :-\ :-\
Entirely carelessness on my part. And it's not something I am likely to do again.
-
:y
-
What pressure do Cessna tyres run at?
-
Is there not a recommended procedure involving decompression before dismantling? Having worked on and in both fighter and large transport aircraft for 40 odd years, this was invariably the case. But perhaps for light aircraft there is no set procedure in this instance. :-\ :-\ :-\
Have a read of the link I posted, suggests deflating prior to slackening the hub nut. Always.
Entirely carelessness on my part. And it's not something I am likely to do again.
It's an effective learning tool ;)
-
Given where the tyre was nestled at the time I'm surprised it was only the five nuts on the wheel that went tight! ;D