Omega Owners Forum
Chat Area => General Car Chat => Topic started by: Darth Loo-knee on 14 May 2010, 18:58:21
-
Only done 68,000 miles, sounds so quiet :y
Booked in for an MOT on Monday so fingers crossed :)
I am wondering if BOSE will go in it? bet it would sound pretty good :D might have a look tomorrow to see if there is the big connector in the footwell... as a 600 (non bose) stereo has gone straight in :y
-
Will your freestanding hairdryer fit in the boot though? ;D ;D
-
sod the bose....
what about a v6 :y
-
Only done 68,000 miles, sounds so quiet :y
Booked in for an MOT on Monday so fingers crossed :)
I am wondering if BOSE will go in it? bet it would sound pretty good :D might have a look tomorrow to see if there is the big connector in the footwell... as a 600 (non bose) stereo has gone straight in :y
Try starting the engine then
-
sod the bose....
what about a v6 :y
Ah we could be on a similar wave length Jimbob :y
-
I have as it happens a Vectra Gearbox and a couple of 3.0 engines lying around ;D
So it maybe on the cards ;)
Obviously it would not be as fast as Martin's car ::) ;D :P
-
I have as it happens a Vectra Gearbox and a couple of 3.0 engines lying around ;D
So it maybe on the cards ;)
Obviously it would not be as fast as Martin's car ::) ;D :P
Well it is running properly again! ;D ;D
-
I have as it happens a Vectra Gearbox and a couple of 3.0 engines lying around ;D
So it maybe on the cards ;)
Obviously it would not be as fast as Martin's car ::) ;D :P
Well it is running properly again! ;D ;D
Thats it then, I don't stand a chance ;D
-
sod the bose....
what about a v6 :y
Apparently a nightmare to do :-?
The engine is so tight within the engine bay that manifolds are rather a pain to do. Also there are some over heating problems when the right sized rad isn't fitted :-[
A little bit of himework needed me thinks...
Now what about a 3.0 engine in the back :o
-
Have you gone up in the world youth ;D
-
sod the bose....
what about a v6 :y
Apparently a nightmare to do :-?
The engine is so tight within the engine bay that manifolds are rather a pain to do. Also there are some over heating problems when the right sized rad isn't fitted :-[
A little bit of himework needed me thinks...
Now what about a 3.0 engine in the back :o
Hmm rear/mid - very interesting
-
I have as it happens a Vectra Gearbox and a couple of 3.0 engines lying around ;D
So it maybe on the cards ;)
Obviously it would not be as fast as Martin's B120 ;D :P
Oh I dunno :-/ :D ;D
-
sod the bose....
what about a v6 :y
Apparently a nightmare to do :-?
The engine is so tight within the engine bay that manifolds are rather a pain to do. Also there are some over heating problems when the right sized rad isn't fitted :-[
A little bit of himework needed me thinks...
Now what about a 3.0 engine in the back :o
Hmm rear/mid - very interesting
Was going to suggest this myself.
Well when you were fixing my gearbox, you did say you wanted a project to get your teeth into ?? ::)
Come on you know you want to do the engine in the back route..... even just for the look to see on the face of some young spotty kid in his scooby ::)
-
i don't think lovely and Corsa should be used in the same sentence ;D
-
i don't think lovely and Corsa should be used in the same sentence ;D
Kids today, a few hairs round their dick and look what they come out with ;D
-
i don't think lovely and Corsa should be used in the same sentence ;D
Kids today, a few hairs round their dick and look what they come out with ;D
Just my opinion :y
Took my test in one, Y Plate 1.2, horrible little things! Rock hard seats!
-
[media]http://www.youtube.com/watch?v=iHTm4aPwfwY[/media]
[media]http://www.youtube.com/watch?v=wjJ-WZp4eGg[/media]
[media]http://www.youtube.com/watch?v=xjrgAp82ENc&feature=related[/media]
-
i don't think lovely and Corsa should be used in the same sentence ;D
Kids today, a few hairs round their dick and look what they come out with ;D
:y :y :y :y :y :y :y :y :y :y :y ;D ;D ;D ;D ;D ;D ;D ;D
-
sod the bose....
what about a v6 :y
Apparently a nightmare to do :-?
The engine is so tight within the engine bay that manifolds are rather a pain to do. Also there are some over heating problems when the right sized rad isn't fitted :-[
A little bit of himework needed me thinks...
Now what about a 3.0 engine in the back :o
as for the overheating use a rad for a matrix you would be nice and warm ;D ;D ;D ;D :y
on a serious note it can be done me and my mate fitted a 2.0redtop to a nova the alternator was the only problem.burning gear got it to fit :y
plus got proper shafts and the antiroll bar spacers etc kit cost £1200 I think ive still got the manual somwhere.
-
Daz, just cut half the bulkhead out and fit the damn engine the right way round ;) :y ;D ;D
-
Well the little Flier pasted its MOT today without even an advisery :y
So when I get back I may advertise it :)
-
Well the little Flier pasted its MOT today without even an advisery :y
So when I get back I may advertise it :)
Chav. ;D