Omega Owners Forum
Newbie Area => Newbie Welcome Area => Topic started by: peterklepec on 10 March 2008, 21:24:11
-
Hi all!
We ported x25xe (1997 omega v6) to frontera and killed imobiliser in the process. So we opted for megasquirt instead. I have great problems getting info on several key components that i need to start tuning. (we successfuly startted engine but did not get much further ) i will list the components that i need info on, and all data will be greatly apriciated.
- I dont know firing order on cylinders.
-can someone confirm thatx25xe has 60 teeth on crank wheel and missing 2 teeth.
-lamda sensor is it narrow band or wide band (i know there are 2 of them)
what would be correct pulse timing for cranking.
these are info that i found and i base my settings on(i picked info up from calibra of the same build year):
Engine: C25XE Ecotec
2498cc - 24 valve - 6 Cylinder
Multipoint (sequential) Fuel Injection
Quad Camshafts
Catalytic Converter
Bosch Motronic 2.8 ECU
front wheel drive
169 bhp @ 6000 rpm
167.4 ft/llbs torque @ 4200 rpm
148 mph max
0-60 mph in 7.3 sec (0-100 kph in 7.8 sec)
0-7000 revs - 6750 redline limited
maybe someone has base settings for this engine?
this is my first post here and english is not my native language, so please be kind.
I thank you for reading this post any help will be greatly apriciated.
-
You may be better posting in the Omega Help section, as more likely to get an accurate answer in that section :)
-
Hi and welcome :y
-
Hi & a warm welcome to the OOF :y
-
"Hello" and Welcome :)
-
Hi and welcome to the OOF :y
-
Hi and welcome.
-
Hi, welcome to the forum and good luck with the project :y
-
Hello & welcome :)
-
welcome to thr forum hope you mak it
-
Hi all!
We ported x25xe (1997 omega v6) to frontera and killed imobiliser in the process. So we opted for megasquirt instead. I have great problems getting info on several key components that i need to start tuning. (we successfuly startted engine but did not get much further ) i will list the components that i need info on, and all data will be greatly apriciated.
- I dont know firing order on cylinders.
-can someone confirm thatx25xe has 60 teeth on crank wheel and missing 2 teeth.
-lamda sensor is it narrow band or wide band (i know there are 2 of them)
what would be correct pulse timing for cranking.
these are info that i found and i base my settings on(i picked info up from calibra of the same build year):
Engine: C25XE Ecotec
2498cc - 24 valve - 6 Cylinder
Multipoint (sequential) Fuel Injection
Quad Camshafts
Catalytic Converter
Bosch Motronic 2.8 ECU
front wheel drive
169 bhp @ 6000 rpm
167.4 ft/llbs torque @ 4200 rpm
148 mph max
0-60 mph in 7.3 sec (0-100 kph in 7.8 sec)
0-7000 revs - 6750 redline limited
maybe someone has base settings for this engine?
this is my first post here and english is not my native language, so please be kind.
I thank you for reading this post any help will be greatly apriciated.
Is the engine an X25 or a C25 firstly
im only familiar with an x25 the lamba sensors are wideband sensors and the ecu is actuall a motronic 2.8.1 or can be a 2.8.3 depending on yr only difference is a PAS sensor firing order is 1-2-3-4-5-6 according to haynes
the cranksenor i have no idea i know its a hall effect sensor but thats all i know
-
Welcome to the forum :y
-
Hi and welcome....good luck with the project :y
-
Hello & Welcome :y
-
Welcome to the Forum :y
-
Hi peterklepec, welcome to the forum.
-
it is 1997 omega x25xe
-
Hi and welcome to the site :y
Good luck with the project 8-)
-
Welcome, good luck and enjoy the forum. :)
-
Hello and welcome :y
-
Hello and welcome to the best Omega Forum on the Net :y