Omega Owners Forum

Omega Help Area => Omega General Help => Topic started by: MartinP on 26 November 2006, 16:55:55

Title: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 26 November 2006, 16:55:55
Went about changing the oil today, got the bits together, jacked the car up and drained the oil...

So far so good.

Lent on a spanner on the filter cap and the whole body starts turning  :-?

15 minutes later got the body off, (the threaded boss in the body is free floating)

then had to heat the aluminium body up to crack the cap free. As the title, 15 Nm it wasn't

Now stuck as I need to replace the (now) three bits of seal under the filter body before I can put it together and go to work.  :(
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: Marks DTM Calib on 26 November 2006, 17:53:44
Do you have any flange sealent......this will work as a temporary measure.....

Note, its easy to fit once the cap is off as the threaded centre boss has a hex on it (27mm I think....)
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: Matchless on 26 November 2006, 18:24:58
Its too late now but....if you come across this problem again then get a second pair of hands to hold the filter body with a strap wrench whilst you get a 24mm socket and breaker bar on the cap nut,  get some load on the bar then smack it (the bar) with a hammer.
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 26 November 2006, 18:49:42
No sealant of any kind, (until I do the cam covers)

 :y It is a 27mm

After getting it on the floor and warmed up, I held the body with a chain type filter wrench and still had to whack the ring spanner with a hammer.


Thanks for the comments

will resort to the neighbours Merc to get me to the local Vaux shop in the morning.
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 26 November 2006, 18:55:45
Mark/Pete

As an aside,

Do you have the seal number, and is there suposed to be a seal in the drain plug? Number?

The X30XE drawing I have shows an angledfilter seating, not a straight fit onto the engine so I don't wan't to quote this number to someone who may know less than me  ;)
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: sounds2k on 26 November 2006, 19:41:01
I had the same problem with mine ... ended up putting the casing in a vice and then using the 27mm socket on the end of a 2 ft breaker bar, even then it was tight !!

the hollow bolt that fixes the housing to the block (with a hole through the middle) is fixed using a 12mm hex driver, torque up to 45 Nm / 33 lbf. ft.

what engine number is it as some parts are different ... it appears that the filter housing my have straightened out later !!

my previous and current miggy's both had a straight filter casing ...
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: Markjay on 26 November 2006, 21:52:59
issunaz, who tightened it last time - garage? if so do you know which one...? name and shame them here...

Title: Re: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 26 November 2006, 22:42:43
Car was privately owned, down south, the guy owned his own company and had his mechanic service the 7 LPG converted vehicles and his car obviously.

As I was (still am) leaking oil slightly I hadn't changed the filter, only poured new stuff in the top  :-[ :-[
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 26 November 2006, 22:50:41
Quote
I had the same problem with mine ... ended up putting the casing in a vice and then using the 27mm socket on the end of a 2 ft breaker bar, even then it was tight !!

the hollow bolt that fixes the housing to the block (with a hole through the middle) is fixed using a 12mm hex driver, torque up to 45 Nm / 33 lbf. ft.

what engine number is it as some parts are different ... it appears that the filter housing my have straightened out later !!

my previous and current miggy's both had a straight filter casing ...


The oil filter housing is pressure diecast mazak (Zinc), the cap has a male thread as part of the casting so it screws directly into the diecast body.

The filter housing body has a floating, threaded stud in the base which needs a 27mm socket to fit to the engine casing. the seal that sits in the mating face of the engine block has hardened and broke when I pratted about trying to get the housing off. :(

Title: Re: Oil filter cap 15Nm MY ARSE
Post by: sounds2k on 26 November 2006, 23:51:51
Quote
The oil filter housing is pressure diecast mazak (Zinc), the cap has a male thread as part of the casting so it screws directly into the diecast body.

The filter housing body has a floating, threaded stud in the base which needs a 27mm socket to fit to the engine casing. the seal that sits in the mating face of the engine block has hardened and broke when I pratted about trying to get the housing off. :(

hmmm ... well, I'm still not entirely sure we are talking about the same thing !!

(http://i42.photobucket.com/albums/e327/n0ddy/miggy/oilfilterhousing.png)

I'm talking about item 12 - the sealing ring that goes between the filter housing and the engine block. It's P/N 90573241 for engine nos. 08300419 to 080843415, P/N 9240161 from engine no. 0843416 onwards - hence the question about the engine number ... and yes the filter housing (item 11) is straight on both my current and previous miggy's - not angled as shown.

the bolt I was referring to is item 13 in the picture - and requires a 12mm hex bit

... are we talking about the same part?  :-/
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 27 November 2006, 10:05:47
Quote
Quote
The oil filter housing is pressure diecast mazak (Zinc), the cap has a male thread as part of the casting so it screws directly into the diecast body.

The filter housing body has a floating, threaded stud in the base which needs a 27mm socket to fit to the engine casing. the seal that sits in the mating face of the engine block has hardened and broke when I pratted about trying to get the housing off. :(

hmmm ... well, I'm still not entirely sure we are talking about the same thing !!

(http://i42.photobucket.com/albums/e327/n0ddy/miggy/oilfilterhousing.png)

I'm talking about item 12 - the sealing ring that goes between the filter housing and the engine block. It's P/N 90573241 for engine nos. 08300419 to 080843415, P/N 9240161 from engine no. 0843416 onwards - hence the question about the engine number ... and yes the filter housing (item 11) is straight on both my current and previous miggy's - not angled as shown.

the bolt I was referring to is item 13 in the picture - and requires a 12mm hex bit

... are we talking about the same part?  :-/


Yes..er No!

This one is definitely a retained fixing through the body.

Have been to the Vaux shop, they show the same drawing.

They also pulled up the seal numbers for the reg/engine number and the engine number preceeds the oil filter assembly.

Their records show a spin on filter type

I will put a pic up later
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: sounds2k on 27 November 2006, 19:13:30
hmmm ..... I wonder if the engine has been swapped at some point? Does it have the extended plenum chamber, as I thought retail MV6's were post mini-facelift so would have this ... ???
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: TheBoy on 27 November 2006, 19:21:53
Quote
hmmm ..... I wonder if the engine has been swapped at some point? Does it have the extended plenum chamber, as I thought retail MV6's were post mini-facelift so would have this ... ???
Not all - my retail mini facelift MV6 has proper (and cheaper) oil filter. The paper element one appear to come in at some point in late 98, early 99.
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 27 November 2006, 20:48:21
Right, is now sorted,

This is the filter body and cap
(http://i3.photobucket.com/albums/y99/issunaz/Omega/Gen/Filterhousing.jpg)

This is the floating bush (27mm socket as Mark advised) in the bottom of the body, this has an extra seal. I now know that this seal is part  No 90573241, which is the same as on the EPC for the early models
(http://i3.photobucket.com/albums/y99/issunaz/Omega/Gen/Filterhousingbody.jpg)

Job took about 20 mins once I had the seal. Lookers at Star City had 6 newer seals in stock and non of the older type so I had to go back 1 hour later once they had got one delivered.
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: sounds2k on 29 November 2006, 18:24:25
glad to hear you got it sorted in the end ... but what a PITA !!

well at least you shouldn't have any more problems with it being done up too tight so long as you're the one doing the changes from now on  :)
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: sounds2k on 29 November 2006, 18:27:48
Quote
Quote
hmmm ..... I wonder if the engine has been swapped at some point? Does it have the extended plenum chamber, as I thought retail MV6's were post mini-facelift so would have this ... ???
Not all - my retail mini facelift MV6 has proper (and cheaper) oil filter. The paper element one appear to come in at some point in late 98, early 99.
I meant the extended plenum chamber - it is possible (and not unknown) for the canister type to be swapped for a cartridge type - some people prefer this. I thought the engine changes came at the same time as the internal trim mini-facelift ... ????
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: MartinP on 29 November 2006, 23:21:41
Yeah, will be doing the oil change a bit more regular in future, will get a couple of seals in stock anyway  ;)
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: sounds2k on 03 December 2006, 22:43:41
if it's any consolation ... I changed my oil and filter again today (after the shennanigans of last time) and ... the lid came off no probs, as expected :)

so it goes to show that there shouldn't be any trouble getting it off as long as the monkeys tighten it to the setting cast into the lid ... as if (!!!)  ::)
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: Markjay on 28 December 2006, 16:31:54
Just tried an oil & filter change... couldn't get the oil filter cap off, it was last tightened by Vx... had to abandon the project, I was working at the roadside near my office (while parked in a Pay & Display…) and couldn’t risk getting the entire housing off, which would have meant leaving the car in the Pay & Display while trying to fix the problem… Arghhh.  >:(
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: TheBoy on 28 December 2006, 16:40:38
Quote
Quote
Quote
hmmm ..... I wonder if the engine has been swapped at some point? Does it have the extended plenum chamber, as I thought retail MV6's were post mini-facelift so would have this ... ???
Not all - my retail mini facelift MV6 has proper (and cheaper) oil filter. The paper element one appear to come in at some point in late 98, early 99.
I meant the extended plenum chamber - it is possible (and not unknown) for the canister type to be swapped for a cartridge type - some people prefer this. I thought the engine changes came at the same time as the internal trim mini-facelift ... ????
Yes, extended plenum came in on 3.0 with mini facelift...   ...the paper oil filter did not come in until later though...
Title: Re: Oil filter cap 15Nm MY ARSE
Post by: Taxi_Driver on 28 December 2006, 19:25:02
Quote
Just tried an oil & filter change... couldn't get the oil filter cap off, it was last tightened by Vx... had to abandon the project, I was working at the roadside near my office (while parked in a Pay & Display…) and couldn’t risk getting the entire housing off, which would have meant leaving the car in the Pay & Display while trying to fix the problem… Arghhh.  >:(

Glad my 2.2's got a £1.10+vat oil filter  ;D