Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: HerefordElite on 24 March 2008, 22:23:00
-
I've finaly got round to changing my wishbones and drop links - went ok apart form the weather!!
Real pig getting the bottom ball joint apart - split it with pronged tool then hammered the crap out of the old arm with a 4 foot metal bar :y
Also the rear bolt is awkward to get to - drivers side is not too bad just needed 3 long extensions (about 700mm!!!) to reach it but passenger side is a real fiddle coming at it from the centre of the car see pics :
(http://i273.photobucket.com/albums/jj210/jakeunderhill/DSC01451.jpg)
(http://i273.photobucket.com/albums/jj210/jakeunderhill/DSC01450.jpg)
Lots of messing about to get the rear bush back into the chassis bracket (screwdriver to prise then bolt from below to align then re-fit from above)
All went ok really and it no longer clonks over speedbumps BUT........
the steering wheel isn't centralised now :o what have i done?? ::) :question
-
Suspect you have done nothing, wishbones are a major part of the suspension so would need tracking (and camber idealy) checking after changing.
-
Suspect you have done nothing, wishbones are a major part of the suspension so would need tracking (and camber idealy) checking after changing.
Was going to get camber checked but didn't realise steering wheel could be adjusted by track-rod ends?/ (or am i being dense?)
Wheel was straight before but guess that was set for the worn 'bones?
cheers Mark :y
-
Suspect you have done nothing, wishbones are a major part of the suspension so would need tracking (and camber idealy) checking after changing.
Was going to get camber checked but didn't realise steering wheel could be adjusted by track-rod ends?/ (or am i being dense?)
Wheel was straight before but guess that was set for the worn 'bones?
cheers Mark :y
Steering wheel position is adjustable, shorten one track rod and lengthen the other and it will move...
-
Suspect you have done nothing, wishbones are a major part of the suspension so would need tracking (and camber idealy) checking after changing.
Was going to get camber checked but didn't realise steering wheel could be adjusted by track-rod ends?/ (or am i being dense?)
Wheel was straight before but guess that was set for the worn 'bones?
cheers Mark :y
Steering wheel position is adjustable, shorten one track rod and lengthen the other and it will move...
yeah i new i was being dense :D - would the tyre centre do that while adjusting tracking?
:y
:y
-
would the tyre centre do that while adjusting tracking?
They should, if they're doing it properly, although I've known them to make it worse.
Watch what they're doing. The first thing they should do is to clamp the steering wheel in the "straight ahead" position, and hten adjust the track rods to obtain the correct toe. Effectively you clamp the steering column straignt and then adjust each wheel so it's also straight.
Sometimes they take a short cut and adjust without clamping the steering first, and this is how the steering ends up wonky.
Kevin
-
would the tyre centre do that while adjusting tracking?
They should, if they're doing it properly, although I've known them to make it worse.
Watch what they're doing. The first thing they should do is to clamp the steering wheel in the "straight ahead" position, and hten adjust the track rods to obtain the correct toe. Effectively you clamp the steering column straignt and then adjust each wheel so it's also straight.
Sometimes they take a short cut and adjust without clamping the steering first, and this is how the steering ends up wonky.
Kevin
Thanks Kev i thought they should :y - still can't believe it was so far off centre just because of wear in the old 'bones :o
-
would the tyre centre do that while adjusting tracking?
They should, if they're doing it properly, although I've known them to make it worse.
Watch what they're doing. The first thing they should do is to clamp the steering wheel in the "straight ahead" position, and hten adjust the track rods to obtain the correct toe. Effectively you clamp the steering column straignt and then adjust each wheel so it's also straight.
Sometimes they take a short cut and adjust without clamping the steering first, and this is how the steering ends up wonky.
Kevin
Thanks Kev i thought they should :y - still can't believe it was so far off centre just because of wear in the old 'bones :o
The toe has probably been adjusted to compensate for the wishbone wear - to bring the toe angle back in as the wishbone is (effectively) lengthening.
It's well worth getting a geometry check done, because if toe has gone out, camber will also be off, and this can cause ferocious shoulder wear.
Kevin
-
would the tyre centre do that while adjusting tracking?
They should, if they're doing it properly, although I've known them to make it worse.
Watch what they're doing. The first thing they should do is to clamp the steering wheel in the "straight ahead" position, and hten adjust the track rods to obtain the correct toe. Effectively you clamp the steering column straignt and then adjust each wheel so it's also straight.
Sometimes they take a short cut and adjust without clamping the steering first, and this is how the steering ends up wonky.
Kevin
Thanks Kev i thought they should :y - still can't believe it was so far off centre just because of wear in the old 'bones :o
The toe has probably been adjusted to compensate for the wishbone wear - to bring the toe angle back in as the wishbone is (effectively) lengthening.
It's well worth getting a geometry check done, because if toe has gone out, camber will also be off, and this can cause ferocious shoulder wear.
Kevin
will get it sorted asap - cheers guys :y
-
would the tyre centre do that while adjusting tracking?
They should, if they're doing it properly, although I've known them to make it worse.
Watch what they're doing. The first thing they should do is to clamp the steering wheel in the "straight ahead" position, and hten adjust the track rods to obtain the correct toe. Effectively you clamp the steering column straignt and then adjust each wheel so it's also straight.
Sometimes they take a short cut and adjust without clamping the steering first, and this is how the steering ends up wonky.
Kevin
Thanks Kev i thought they should :y - still can't believe it was so far off centre just because of wear in the old 'bones :o
The toe has probably been adjusted to compensate for the wishbone wear - to bring the toe angle back in as the wishbone is (effectively) lengthening.
It's well worth getting a geometry check done, because if toe has gone out, camber will also be off, and this can cause ferocious shoulder wear.
Kevin
Right got the beast booked in for 4 wheel alignment and camber check tomorrow, any last minute tips?
I've read up a bit about WIM suggesting diff settings dependant on vehicle height (i.e. spring wear) but guessing my local tyre centre will just go with what their computer tells them :-/
-
guessing my local tyre centre will just go with what their computer tells them
That's the danger. The limits on the machines are so wide that there can still be horrendous tyre wear with everything in the green.
For a start, ask them to set the camber at the low end of the range (say 1o10') and get both sides the same. Don't accept it if everything's green but the alignment is obviously asymmetrical. After that you can keep an eye on tyre wear and see what happens.
Mine had about 2o on one side and 2o40' on the other and it was still green. :o
The advantage with Tony at WIM, is that he'll look at how the suspension is sitting and decide what's a good starting point for the camber, as the ideal figure will vary from car to car. Might be worth PM'ing him and see if he can give you any base settings to work from.
Kevin
-
guessing my local tyre centre will just go with what their computer tells them
That's the danger. The limits on the machines are so wide that there can still be horrendous tyre wear with everything in the green.
For a start, ask them to set the camber at the low end of the range (say 1o10') and get both sides the same. Don't accept it if everything's green but the alignment is obviously asymmetrical. After that you can keep an eye on tyre wear and see what happens.
Mine had about 2o on one side and 2o40' on the other and it was still green. :o
The advantage with Tony at WIM, is that he'll look at how the suspension is sitting and decide what's a good starting point for the camber, as the ideal figure will vary from car to car. Might be worth PM'ing him and see if he can give you any base settings to work from.
Kevin
cheers Kev - Pm'd Tony a while back but appreciate he's not a regular visiter
-
guessing my local tyre centre will just go with what their computer tells them
That's the danger. The limits on the machines are so wide that there can still be horrendous tyre wear with everything in the green.
For a start, ask them to set the camber at the low end of the range (say 1o10') and get both sides the same. Don't accept it if everything's green but the alignment is obviously asymmetrical. After that you can keep an eye on tyre wear and see what happens.
Mine had about 2o on one side and 2o40' on the other and it was still green. :o
The advantage with Tony at WIM, is that he'll look at how the suspension is sitting and decide what's a good starting point for the camber, as the ideal figure will vary from car to car. Might be worth PM'ing him and see if he can give you any base settings to work from.
Kevin
cheers Kev - Pm'd Tony a while back but appreciate he's not a regular visiter
With a new centre under construction I would imagine he's probably a busy chap at the moment too.
Get them to set it at the lowish end of the scale and see how you get on. Mine was certainly eating tyres at the 2o end of the scale (most alignment machines have the limit at well over 2o). As I said, however, YMMV as what the camber does dynamically depends on how the suspension has worn.
Kevin