Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: hp7166 on 12 December 2008, 08:29:48
-
Hi Guys
I cant get my heater to work. I Checked the fuse and it seems ok, can anyone help its freezing!!!!
-
have a fiddle with the conections on the blower, i had fualty cons with my 2.5. :y
-
A bit more info needed.
1) Is the blower working?
2) Is the engine getting to operating temp?
3) Are the ventialtion direction controls working with the blow air moving from screen, to face, to foot well in response to the controls
-
A bit more info needed.
1) Is the blower working? No
2) Is the engine getting to operating temp? Yes
3) Are the ventialtion direction controls working with the blow air moving from screen, to face, to foot well in response to the controls
It seems to be but cant really tell as the blowers are not working
-
So the fan for the blowers is not working?
-
Yep
-
Ok
First things to check
A) Is the scuttle empty of water (rear right of the engine bay)
B) Is fuse 33 ok?
-
Sorry about the confusion.
I cleared the scuttle the other week but will checkl again, Fuse looked ok and did try another and it was still the same.
-
Sorry about the confusion.
I cleared the scuttle the other week but will checkl again, Fuse looked ok and did try another and it was still the same.
Ok, climate or standard heating setup?
When you originaly cleared the scuttle drain, was it blocked?
-
Sorry about the confusion.
I cleared the scuttle the other week but will checkl again, Fuse looked ok and did try another and it was still the same.
Ok, climate or standard heating setup?
When you originaly cleared the scuttle drain, was it blocked?
Its Standard Heater Setup, The drain was blocked a bit with gunk no water
-
Ok, so the chances are we are looking at a fan failure.
Next stage is to remove the glove box and start measuring voltages on the fan terminals.
I assume the fan never works, not even on full speed.
-
Ok, so the chances are we are looking at a fan failure.
Next stage is to remove the glove box and start measuring voltages on the fan terminals.
I assume the fan never works, not even on full speed.
No The fan does not work at all, it was working yesterday but i heard like a electric zap/click when driving.
How hard is it to remove the glovebox? I guess i need to get a multi meter?
-
Check the maint guides for changing glovebox lock, that involves removing glovebox.
-
Does anyone have a pic on the fan terminals or with they just be there when i take the box off
-
I have removed the glove box thanks to the guide about 5 mins but cant seem to see the motor to test
here is the pic
(http://i279.photobucket.com/albums/kk156/robhill1983/PC130068.jpg)
-
ok i think i know where is but cant seem to get into the housing
cheers
rob
-
i have been trying all day to get into the housing does any one have any tips
-
sorry guys need to get some help asap if you dont mind i'm desperate
-
Ditto. Sorry for false hope mate, I just changed out my speed controller and climate, and I'm in exactly the same boat..
With the glove box off I hear a short and sharp hiss every time the fan is meant to start. Everything works fine, tested 2 climates 2 speed controllers now.
Re: housing: I see 2 screws at the bottom of the housing, either side, little torx bolts. Try those. Anyone else wanna chip in?
-
Hi All
Got a Service manual from ebay and it shows this
(http://dc97.4shared.com/img/76541544/40d42db6/Heater_Motor.pdf) (http://www.4shared.com/file/76541544/40d42db6/Heater_Motor.html)
Job for the weekend i think. I really hope it works as its freezing in my car at the mo
Here is the link to a bigger picture
(http://dc97.4shared.com/img/76541887/7db0a053/HMP_Tiff_Hotspot_Viewer.pdf) (http://www.4shared.com/file/76541887/7db0a053/HMP_Tiff_Hotspot_Viewer.html)