Omega Owners Forum
Omega Help Area => Omega General Help => Topic started by: marty31 on 01 July 2009, 22:04:41
-
Hi everyone i am new in here but not new to Omegas, i have just bought a 52 plate 2.6 v6 with what i was told a snapped cambelt, when it arrived i had a look over it and the cambelt is on but when i tried to turn the engine over by hand it goes so far but then completely locks up(i was thinking maybe conrod) it took 3 litres of water and seems to have oil in it so i have no idea why it would let go, anyway if anyone can help me find an engine i will appreciate it, i am located near Manchester airport but i can travel for the right engine "PRICE"
Thanks everyone for reading this and thank for any help you can give me.
-
Seen one on Ebay not too long ago for £350
Some on Ebay as we speak
:y
-
The belt is on but is the timing right?
-
belt could have jumped due to failed tensioner. You may find a load of stripped belt teeth in the bottom of the cover, for what its worth.
If you can find a 3.2 lump its practically a straight swap afaik. Not done it myself but i know of another member who has. :-)
-
My last 2.6 went pop when the crankshaft pulley worked loose and then broke the woodruff key off! OUCH.
From experience, I would just replace the engine.
-
a bit off topic, but there seems to be quite a few folks having problems with 2.6's giving up - are they any more feagile than any of the other variants?
Or is it just me being paranoid?
-
a bit off topic, but there seems to be quite a few folks having problems with 2.6's giving up - are they any more feagile than any of the other variants?
Or is it just me being paranoid?
Paranoid
Mine survived a cam pulley slip with no damage
-
The cambelt is on and all teeth are in tact that i can see, when i turn the engine over it will go about half a turn forward and backward, doe anyone have any more info on the 3.2 lump going straight in, is there no problems with ancils or wiring harness??
Also when i get a new engine this unit is surpless so if anyone needs any heads or anything else that may be salvageable its free to a good home if you can collect. i am near manchester airport
-
RobsyMv6 swapped his 2.6 for a 3.2. Think ive spelled his name right. Think he got ex plod and broke the rest of the car for parts.
-
i had a 2.6 and had same symptoms - it had a conrod through the side of the engine!
-
i had a 2.6 and had same symptoms - it had a conrod through the side of the engine!
was acutally two alex !! ;D
-
lmao 5 and 6 mark?
maybe i should have asked for the bottom end back and used it as a coffee table like the v8 on top gear :P
-
i had a 2.6 and had same symptoms - it had a conrod through the side of the engine!
was acutally two alex !! ;D
What did you do with the rest of the engine?
-
Sounds like some teeth have slipped and now a piston is hitting the valve(s) as you turn the engine. Have you got a timing tool from the cambelt kit? You might need to take off the belt and carefully get the engine back to TDC.
On a related note, I might try and make a keyhole camera gadget that can be inserted into the spark plug hole to see if the valve is contacting with the piston. Usefull tool?
-
I have started to strip it down now and there was water in the pipes leading into the plenum chamber, i think water has got in and the engine has hydrauliced, also when i have taken the inlet manifold off you can see some rust marking on number 2 inlet, i would'nt be suprised to see a conrod through the block the more i strip it down. Hopefully i have sorted an engine out with Robsey but i have'nt heard back yet so if anyone else knows where there is a 2.6 v6 engine around for not crazy (ebay) money let me know. i will have a couple of heads once i am finished, if anyone wants them then pick them up i am near manchester airport