Omega Owners Forum

Omega Help Area => Omega General Help => Topic started by: amba on 04 August 2009, 18:13:00

Title: Caliper slider bolts
Post by: amba on 04 August 2009, 18:13:00
Just completed a refurb of all 4 calipers and have decided to replace the front caliper slider bolts with new.What is the correct grease to put on the sliders ?
Title: Re: Caliper slider bolts
Post by: sparkyw666. on 04 August 2009, 18:25:23
i use copper grease works well for me :y
Title: Re: Caliper slider bolts
Post by: Andy B on 04 August 2009, 19:01:09
Quote
i use copper grease works well for me :y

Where's GixerChris?  ::)  ::)  ::)  ;D  ;D
Title: Re: Caliper slider bolts
Post by: sparkyw666. on 04 August 2009, 22:06:38
Quote
Quote
i use copper grease works well for me :y

Where's GixerChris?  ::)  ::)  ::)  ;D  ;D
????
Title: Re: Caliper slider bolts
Post by: Andy B on 04 August 2009, 22:15:02
Quote
Quote
Quote
i use copper grease works well for me :y

Where's GixerChris?  ::)  ::)  ::)  ;D  ;D
????


Chris & I discussed  ::) the use of copper grease on cliper slides a little while back.  ;) ;D ;D ;D :y
Title: Re: Caliper slider bolts
Post by: sparkyw666. on 04 August 2009, 22:20:25
Quote
Quote
Quote
Quote
i use copper grease works well for me :y

Where's GixerChris?  ::)  ::)  ::)  ;D  ;D
????


Chris & I discussed  ::) the use of copper grease on cliper slides a little while back.  ;) ;D ;D ;D :y
oh i get u now :y
Title: Re: Caliper slider bolts
Post by: Seth on 04 August 2009, 22:23:33
Personally, I coat the sliders with engine oil - though obviously only a small amount.
Never had any problems with this method.
Title: Re: Caliper slider bolts
Post by: amba on 04 August 2009, 22:45:38
I am sure read somewhere that it was wise to use a silicone grease,but as never stripped and rebuilt calipers before wanted to use correct stuff...when I pulled old bolts out it felt like a very thick grease so don,t think engine oil would be appropriate.
Title: Re: Caliper slider bolts
Post by: feeutfo on 05 August 2009, 19:23:44
you need a non mineral based(so it doesnt eat the rubber) hi temp(so it doesnt melt) grease(so it lubricates). Usually silicon based often red for some reason. To mark it out as not normal grease i think.

 Do not use copper slip, it is not, i repeat NOT, definately 100% NOT a lubricant. Especially not for brake sliders.

Would have thought Andy would have told you that. :-) (snigger)
Title: Re: Caliper slider bolts
Post by: Andy B on 05 August 2009, 19:25:53
Quote
.....
Would have thought Andy would have told you that. :-) (snigger)

I didn't want to steal you thunder!  ;)  ;)  ;D   ;D :y  :y
Title: Re: Caliper slider bolts
Post by: amba on 05 August 2009, 21:39:08
Just out of interest when I went into local dealers today,I asked the workshop foreman what they used and what was the recommended slider bolt lubricant from Vauxhall.
He stated that they always use "copper slip grease" so I am now puzzled.
I totally understand the logic put forward by Chris which I tend to agree with over that of the dealer...but what should be ussed then ??some say engine oil/copperslip/and now some "red stuff"..Help
Title: Re: Caliper slider bolts
Post by: Andy H on 05 August 2009, 21:54:32
The caliper pistons come into contact with the brake fluid so the grease needs to be compatible with both brake fluid & the seals. I use red rubber grease, little sachets come with the seals if you buy a refurb kit but you can buy a tub of it quite cheaply. Alternatively just use brake fluid, if you have switched to silicone brake fluid use that.

The caliper sliders don't come into contact with brake fluid but they do get hot so copper grease is is good.

PS Copaslip (spelling?) is a trade name for copper grease.
Title: Re: Caliper slider bolts
Post by: 3.2 manual on 26 August 2009, 23:56:39
copper grease is what i use, apply a thin smear to the back of the pads(stops squeel), the bit where pad meets caliper a tiny bit(you dont want it on the pad or disk). in the caliper sliders i use it, although if your not a racing driver any high temp grease should do. never had a problem, even after six years. so if it does like rubber it only does it very slowly!