Omega Owners Forum

Omega Help Area => Omega General Help => Topic started by: devonkev on 13 January 2010, 17:56:11

Title: Help! Urgently need workshop manual for '01 2.2
Post by: devonkev on 13 January 2010, 17:56:11
I'm supposed to be one of 200 people selected to be in the Nissan UK free race on friday morning. I have to get to Silverstone race circuit and I live in Devon.
The water pump went on my omega this morning and luckily didn't take the cambelt with it! Just went to change both and the belt slipped as the pump was barely in one piece. I cant get hold of a manual from anywhere local and postage will take too long. At this rate I wont make it to this race which I was so lucky to win a place in. :'( :'(

I only need to see the pages that show the cambelt/water pump change and I would be so gratefull if someone has a PDF version they could email me or even scan from the book I would happily pay-pal you a few quid. I'm really desparate here.
Thanks
Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: ians on 13 January 2010, 18:15:01
There isn't a Haynes book for that vintage Omega :(, but still worth getting the prefacelift Omega book as 80% is the same. :y

I doubt too much is different in the cambelt/waterpump area - not a difficult job on 4 pot, but worth getting hold of the camlock device if you can.

Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: TheBoy on 13 January 2010, 18:25:17
Brief details emailed to your hotmail account
Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: devonkev on 13 January 2010, 18:26:46
Yeah i was going to try and lock the cams unconventionally, was already making good progress when i overshot the marks (while turning the crank)  and when i went backwards it must have slipped a load of teeth (it was quite obvious something had slipped with the marks completely out now!). Anyway i just need to check exactly where everything needs to be before i can go further.
Not too bothered if its Haynes though as i've seen some on dvd/cd on ebay and i assume they are not Haynes.
If an earlier model is the same then i will gladly let someone scan me their Haynes page ::).
Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: TheBoy on 13 January 2010, 18:28:06
Quote
Yeah i was going to try and lock the cams unconventionally, was already making good progress when i overshot the marks (while turning the crank)  and when i went backwards it must have slipped a load of teeth (it was quite obvious something had slipped with the marks completely out now!). Anyway i just need to check exactly where everything needs to be before i can go further.
Not too bothered if its Haynes though as i've seen some on dvd/cd on ebay and i assume they are not Haynes.
If an earlier model is the same then i will gladly let someone scan me their Haynes page ::).
some photos emailed. from a 2.0, but same setup. Hope that helps
Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: Abiton on 13 January 2010, 18:31:43
Is that photos of the Haynes pages? If not, I've just scanned/pdfed 'em, if you want to PM me your hotmail addy, I'll mail them to you.
Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: TheBoy on 13 January 2010, 18:32:26
Quote
Is that photos of the Haynes pages? If not, I've just scanned/pdfed 'em, if you want to PM me your hotmail addy, I'll mail them to you.
yup. Hopefully he is sorted now
Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: TheBoy on 13 January 2010, 18:35:24
wave as you drive past Brackley :y
Title: Re: Help! Urgently need workshop manual for '01 2.2
Post by: devonkev on 13 January 2010, 23:17:43
Many many thanks! Job done! Sorry i didn't reply sooner but as soon as I had the info I was outside under the bonnet!

Thanks everyone.