Omega Owners Forum

Omega Help Area => Omega General Help => Topic started by: Liam on 29 July 2010, 19:38:06

Title: Head swap noob advice
Post by: Liam on 29 July 2010, 19:38:06
Well thanks to Elite Pete for supplying a replacement head and the two pulleys that ate each other, the head swap is now under way. Never done one before so need some noob advice...

How clean to the mating surfaces need to be? Are we talking shiny new metal clean, which will take some rubbing with fine wet and dry, or is that too aggressive for the ally head? If so is a crap-scraped-off-and-degreaser-clean level sufficient?

Other than that all going good so far. Pete I managed to drill out that broken exhaust manifold stud at work today.

Oh - I was reading the maintenance guide on the headgasket replacement which is very handy, and it references a guide by Mark DTM on servicing the hydraulic followers. But I can't find that guide?? What can/needs to be done on those? They look pretty unserviceable at first glance other than checking the little hole isn't full of crap which they aren't.

Cheers,

Liam
Title: Re: Head swap noob advice
Post by: plym ian on 29 July 2010, 19:48:34
What caused your pulleys to eat each other?
Title: Re: Head swap noob advice
Post by: Liam on 29 July 2010, 20:02:25
http://www.omegaowners.com/forum/YaBB.pl?num=1278179054/0
Title: Re: Head swap noob advice
Post by: RobG on 29 July 2010, 21:27:17
Quote
Well thanks to Elite Pete for supplying a replacement head and the two pulleys that ate each other, the head swap is now under way. Never done one before so need some noob advice...

How clean to the mating surfaces need to be? Are we talking shiny new metal clean, which will take some rubbing with fine wet and dry, or is that too aggressive for the ally head? If so is a crap-scraped-off-and-degreaser-clean level sufficient?

Other than that all going good so far. Pete I managed to drill out that broken exhaust manifold stud at work today.

Oh - I was reading the maintenance guide on the headgasket replacement which is very handy, and it references a guide by Mark DTM on servicing the hydraulic followers. But I can't find that guide?? What can/needs to be done on those? They look pretty unserviceable at first glance other than checking the little hole isn't full of crap which they aren't.

Cheers,

Liam
http://www.omegaowners.com/forum/YaBB.pl?num=1163080380 :y
Title: Re: Head swap noob advice
Post by: Marks DTM Calib on 30 July 2010, 09:56:12
Quote
Well thanks to Elite Pete for supplying a replacement head and the two pulleys that ate each other, the head swap is now under way. Never done one before so need some noob advice...

How clean to the mating surfaces need to be? Are we talking shiny new metal clean, which will take some rubbing with fine wet and dry, or is that too aggressive for the ally head? If so is a crap-scraped-off-and-degreaser-clean level sufficient?

Other than that all going good so far. Pete I managed to drill out that broken exhaust manifold stud at work today.

Oh - I was reading the maintenance guide on the headgasket replacement which is very handy, and it references a guide by Mark DTM on servicing the hydraulic followers. But I can't find that guide?? What can/needs to be done on those? They look pretty unserviceable at first glance other than checking the little hole isn't full of crap which they aren't.

Cheers,

Liam

Get something flat (greater than the width of the head) and wrap some wet and dry round it (200+ grit) and wet it.

Then rub it the full length of the head until its clean and shiney.

Does not take long at all and is very little effort

Title: Re: Head swap noob advice
Post by: Liam on 30 July 2010, 10:14:35
Thanks guys :y
Title: Re: Head swap noob advice
Post by: 2woody on 30 July 2010, 11:42:29
as with any other engine parts - I'd say they're only really clean enough if you'd be confident licking them.
Title: Re: Head swap noob advice
Post by: Liam on 30 July 2010, 11:46:48
Quote
as with any other engine parts - I'd say they're only really clean enough if you'd be confident licking them.

Best engine building rule of thumb evvaaar  :y
Title: Re: Head swap noob advice
Post by: Elite Pete on 30 July 2010, 11:53:14
Quote
as with any other engine parts - I'd say they're only really clean enough if you'd be confident licking them.
You want to see some of the places i've had my tongue ::) ;D
Title: Re: Head swap noob advice
Post by: davethediver on 30 July 2010, 12:13:37
Quote
Quote
as with any other engine parts - I'd say they're only really clean enough if you'd be confident licking them.
You want to see some of the places i've had my tongue ::) ;D

 ;D ;D ;D ;D
Title: Re: Head swap noob advice
Post by: 2woody on 30 July 2010, 12:17:21
you want to see some of the engines I've had my tongue in !