Omega Owners Forum

Omega Help Area => Omega Electrical and Audio Help => Topic started by: twiglet on 22 August 2011, 22:55:51

Title: CCR2006 to NCDC2013 upgrade
Post by: twiglet on 22 August 2011, 22:55:51

This would be in 2002 2.2 CDX. I've got the HU and GID, plus the aerial for the GPS.

Is it then just a case of old HU + screen out, new HU + screen it? Or does the wiring harness have to be changed to suit?

TIA  :y

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: RobG on 22 August 2011, 22:56:58

Quote

This would be in 2002 2.2 CDX. I've got the HU and GID, plus the aerial for the GPS.

Is it then just a case of old HU + screen out, new HU + screen it? Or does the wiring harness have to be changed to suit?

TIA  :y

PM sent

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: twiglet on 22 August 2011, 23:07:34

All sorted now, thanks to Rob  :y

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: VXL V6 on 22 August 2011, 23:09:19

Ah, a little loom required.....

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: TheBoy on 23 August 2011, 18:49:43

Aye, minor mod to TM loom.

I've kept my loom from Goldie, so I have the details

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: VXL V6 on 25 August 2011, 20:42:36

IIRC the minimum you can get away with is Headunit pin 32 to display unit 10 and head unit pin 33 to display unit pin 11.

Obviously you will need to remove the existing pin 10 and 11 connections and tape them out of the way. I think you also have to remove pin 9 as well, though I haven't got my document to hand at the moment.   

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: albitz on 25 August 2011, 22:01:43

Sounds like I need to remove the trafficmaster loom from bluey the breaker. ::) ;D

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: TheBoy on 26 August 2011, 09:02:45

Quote

IIRC the minimum you can get away with is Headunit pin 32 to display unit 10 and head unit pin 33 to display unit pin 11.

Obviously you will need to remove the existing pin 10 and 11 connections and tape them out of the way. I think you also have to remove pin 9 as well, though I haven't got my document to hand at the moment.   

Albs - thats the CAN I was talking about in PMs :y

Also, on the screen, you need to connect pin 1 to pin 34 if ever you want to run any diagnostics on it.

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: albitz on 26 August 2011, 09:07:01

Not confident of doing that tbh, but I think I know a man who is. ;) ::)

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: Lazydocker on 26 August 2011, 13:14:15

Quote

Not confident of doing that tbh, but I think I know a man who is. ;) ::)

Sounds like you want a favour then ::) ::) :D :D

Title: Re: CCR2006 to NCDC2013 upgrade
Post by: albitz on 26 August 2011, 22:16:34

Possibly. ::) :D..........thing is, my 2013 may well be in full working order now. Swapping the board with TB,s has cured the problem of no sound. :) But without plugging it and its paired screen into a fully Bose enabled setup, I dont know.
Unless of course that gobbledegook Tb was talking a couple of posts previously is a way of avoiding that. :-/