Omega Owners Forum
Chat Area => General Car Chat => Topic started by: Gaffers on 29 September 2011, 19:17:31
-
For the correct connections for my tomasetto valve rather than the plumbing adaptors I fitted which had the smallest of leaks :(
After that though I am booked in with Aron Autogas down the road for an inspection on my way to the land of good wine and smelly armpits. Due to the location of the vapouriser i have fitted a heat sheild for the small section of polyflex in relative proximity to the exhaust manifold and egr. I know it is a contraversial issue but I am leaving nothing to chance.
Again a massive thanks to Kevin who not only drilled and tapped the inlet for me but also did the loom on the front end. Also to Paul and Chris for the polyflex routing, I had a look recently on the ramps and it looks very very smart.
As TB said recently it is very humbling to have such good mates on here :y
-
never met him, but he was excellent getting the extra little bits i needed for my install :y
-
Got to admit, I can't fault him :y ( when you can get him to a phone that is ) ;D ;D
-
I have found he is getting better at answering the phone. 70% success rate this week ;Do
-
never met him, but he was excellent getting the extra little bits i needed for my install :y
That may have been because it was me ordering them though ;) ;D
-
Guffer, you are more than welcome... Wasn't much really ;) Have you put the extra clips in that were required? ???
Best of luck with it all and be sure to let us know... Apparently (according to Teilo) Arun are pretty reasonable so should be ok :y
-
Along the towbar yes everywhere else was ok right? ???
-
Along the towbar yes everywhere else was ok right? ???
ISTR we were running short :-\ Although the length of the car is within spec (60cms between fixings :o) I would check that they're no more than 30ish cms apart ;)
-
I remember now there was one missing which I did add later. From what I saw every single one was within 30cm of the next ;)
-
Well it passed with flying colours. No problems or advisories so thanks again to all Ho helped. Problem is now it seems to have dropped the map and I don't remember if I packed the ish cable ....... :-\
-
Good news on the cert Guffers :y
-
someone clearly messed up here!
Who forgot to put gravel down the intake manifold :D ;D ;D
-
Congrats G, you're officially a gas sniffer now! ;D :y
-
someone clearly messed up here!
Who forgot to put gravel down the intake manifold :D ;D ;D
I couldn't bring myself to do it. I felt too sorry for him after he'd mauled his front wing on my garage door pillar. :-X
-
someone clearly messed up here!
Who forgot to put gravel down the intake manifold :D ;D ;D
I couldn't bring myself to do it. I felt too sorry for him after he'd mauled his front wing on my garage door pillar. :-X
Ahhh, now Melchett has kept that quiet ;D
-
someone clearly messed up here!
Who forgot to put gravel down the intake manifold :D ;D ;D
Wasn't me, not been near the engine bay. ;D
-
someone clearly messed up here!
Who forgot to put gravel down the intake manifold :D ;D ;D
I couldn't bring myself to do it. I felt too sorry for him after he'd mauled his front wing on my garage door pillar. :-X
Ahhh, now Melchett has kept that quiet ;D
Yes thank you Kev ::)
I decided that my car needs symetry so I decided to put my one good front wing up against Kevs garage pillar, I hope with little lasting damage to your door KW.....
Anyway I'm having the time of my life here. Not only did Tonga neat France I am hereto give them loads of grief about it in person ;D