Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega Electrical and Audio Help / Re: CCRT display problem ?

« on: 02 February 2012, 13:07:35 »

Hi.

I found the real "problem".. which is not one.

I re-open my "new" display, and compare it to the broken one. Ther is a BIG hardware difference.

The broken one have more wire from the PCB to the glass : the brown wire in this picture are only in the broken display :



at the left of the display, we can see a small component, which I this is a teperature sensor. The brown wire re connect to a glass. I think this glass will be darker if the temperature is higher. My new display doesn't have this fonction.



So the background of the display is darker in the broken one, and its darkness increase with the temperature.

the "new" display is older.

2

Omega Electrical and Audio Help / Re: CCRT display problem ?

« on: 31 January 2012, 11:23:35 »

sorry for the poor quality.


when the display is cold :




and when it is hot (aften 30 minutes driving)

3

Omega Electrical and Audio Help / CCRT display problem ?

« on: 30 January 2012, 13:39:50 »

Hi.

I change the CCRT display of my vectra. the old one was totaly dead. I bought a used one from poland, swap the internal EEPROM to get my configuration, and place it in my vectra. It works, but, it seems to have a probleme : the "off pixel" and "off  icons" are really bright! in some case, hours become difficult to read, and the other lines are really ugly.

Any idea of the problem?

thanks

4

Omega Electrical and Audio Help / Re: NCDR1100, CID, CDC3 programming

« on: 14 September 2011, 11:44:53 »

but I must pay for that [smiley=thumbdown.gif]
of course, this is not realy expensive, but security code + programming the CDC3 + programaming the CID + .... is expensive!

that's why I'm trying to do it myself.

5

Omega Electrical and Audio Help / Re: NCDR1100, CID, CDC3 programming

« on: 12 September 2011, 09:56:13 »

that's what I done!

I remove the 93C56 form the CID, read it with an universal programmer at my office, then resolder it.

all my dump have been done by this way.

PS : i'm an electronic engineer.

6

Omega Electrical and Audio Help / Re: NCDR1100, CID, CDC3 programming

« on: 11 September 2011, 11:44:28 »

. Dumps from the CID are unreliable unless you lift the chip IME.  Config locations seem to vary in NCDx depending on board revisions.

Whart do you mean by that? I d'ont understand.

7

Omega Electrical and Audio Help / NCDR1100, CID, CDC3 programming

« on: 09 September 2011, 15:51:28 »

Hi.
I apologize if my english is not good.


I have a NCDR1100 and a CID which are paired together, and come from an astra G. CID identifier is KK.
I aad to this configuration a CDC3 TA, and i convert it in TB with a dump found on the internet. it works, but i have CDC safe... of course, the CDC3 is not paired to the NCDR/CID.


now, i'm going to put it in a vectra B.
so i need your help. i see in this forum some people who can do that.

1) I don't have the car pass of the astra, so I want to decrypt the security code with the CID and the NCDR1100 dump (dump available)
2) I want to paired my CDC3.
3) i'm looking for the configuration of the CID : code index, wheel size. adress? is it crypt?
4) vectra B normally have a CID KH, not KK or KJ. the first difference is mechanical. my KK is smaller. the 3 metal plate is on the bottom edge on the KK ans at the to edge in the KH. so the display is up side down. it's not a problem for me : I open my CID, cut the good copper root, et pull it to the 0V, and now, the display is in the good side. but normally, it should be done by software. I think a bit in th 93C56 give the the screen orientation. which one is it?

i have the dump of my NCDR110, CDC3 and CID.



thanks for your help.

8

Newbie Welcome Area / Hello

« on: 09 September 2011, 14:24:32 »

Hello, I'm french, and I drive a vectra B 2.0 16V automatic.

google found me here a topic which interest me.