1
Omega General Help / Re: Diesel fuel line diameter
« on: 10 December 2014, 09:36:43 »
Just needed to know the right size because I am
going to part shop soon.
going to part shop soon.
- 14 March 2026, 15:54:32
- Welcome, Guest
News:
Please play nicely. No one wants to listen/read a keyboard warriors rants....
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Omega General Help / Re: Diesel fuel line diameter
« on: 10 December 2014, 08:05:57 »
plastic tubes outside diameter may be 8 mm becaue 9 mm spanner
was a bit loose ,tube is quite thin and shrinked so is inner diameter
then 8 or 6 mm ?
was a bit loose ,tube is quite thin and shrinked so is inner diameter
then 8 or 6 mm ?
3
Omega General Help / Re: Help with Diesel leak
« on: 10 December 2014, 07:59:57 »
I had similar leak better check first that all the black boxs screws are tight
mine was all lose then the only the pump cover gasget may leak but the
pump is tilted so it may
look that the lower gasket leaks... so better check these first
mine was all lose then the only the pump cover gasget may leak but the
pump is tilted so it may
look that the lower gasket leaks... so better check these first
4
Omega General Help / Diesel fuel line diameter
« on: 09 December 2014, 23:07:43 »
What is the inner diameter of the black fuel line hose next to yellow one in the picture.
Later the line changes to thicker rubber line is its diameter same too ?
Later the line changes to thicker rubber line is its diameter same too ?
5
Omega General Help / Re: Omega 2.5 TD Dieselpump electric cover leaks
« on: 02 October 2014, 20:10:08 »
I am meanig black box cover ( electric cable
goes in via this cover )
Now if have found some pics on oldsite
in first pic the box is cirled red
http://oldsite.omegaowners.com/forum/YaBB.pl?num=1275050663/0
and in later pic you see the green green o-ring seal
and because wires get throgh that seal you really
need to unsolder the wires from metal top cover
which you are referring .
so choices are unsolder the wires and renew the
seal or use instant gasket ??
goes in via this cover )
Now if have found some pics on oldsite
in first pic the box is cirled red
http://oldsite.omegaowners.com/forum/YaBB.pl?num=1275050663/0
and in later pic you see the green green o-ring seal
and because wires get throgh that seal you really
need to unsolder the wires from metal top cover
which you are referring .
so choices are unsolder the wires and renew the
seal or use instant gasket ??
6
Omega General Help / Re: Omega 2.5 TD Dieselpump electric cover leaks
« on: 01 October 2014, 08:10:57 »
too difficult so does it work if I loosen the screws
( pump in place )
and put some heat and diesel resistant silicone
around the cover ??
( pump in place )
and put some heat and diesel resistant silicone
around the cover ??
7
Omega General Help / Re: Omega 2.5 TD Dieselpump electric cover leaks
« on: 01 October 2014, 08:09:53 »
too difficult so does it work if I loosen the screws
( pump in place )
and put some heat and diesel resistant silicone
around the cover ??
( pump in place )
and put some heat and diesel resistant silicone
around the cover ??
8
Omega General Help / Re: Omega 2.5 TD Dieselpump electric cover leaks
« on: 01 October 2014, 06:51:36 »
Just called to Bosch diesel service about the leak.
They said that do not open the cover if opened the
pump must be adjusted , bring the pump here
they put it in bench and adjust it !
I said that only electric cable cover leaks only seal
must renew why need take the whole pump
off you just open 4 screws and renew the seal ?
He explained that to chage the seal wiring must
desolder first and then cover can be taken off
and renew the seal same time they change all
seals etc would cost about 1000 euros !
What if just loose the cover slighly and but some
glue sealt on the cover ?
They said that do not open the cover if opened the
pump must be adjusted , bring the pump here
they put it in bench and adjust it !
I said that only electric cable cover leaks only seal
must renew why need take the whole pump
off you just open 4 screws and renew the seal ?
He explained that to chage the seal wiring must
desolder first and then cover can be taken off
and renew the seal same time they change all
seals etc would cost about 1000 euros !
What if just loose the cover slighly and but some
glue sealt on the cover ?
9
Omega General Help / Omega 2.5 TD Dieselpump electric cover leaks
« on: 30 September 2014, 17:42:38 »
This black cover leaks 
, what is inside the cover ? . Can I just open the cover and change the sealant or is the job for professionals.
I tried to tighten the screws
Starange that 3 screws are torx but one is some kind of hex bolt 6mm ?? can't see it properly I tried to tighten it but my socket was too thick..
jpg images
, what is inside the cover ? . Can I just open the cover and change the sealant or is the job for professionals.I tried to tighten the screws
Starange that 3 screws are torx but one is some kind of hex bolt 6mm ?? can't see it properly I tried to tighten it but my socket was too thick..
jpg images
10
General Car Chat / Combo flat battery , no start until ....
« on: 20 May 2014, 06:43:14 »
Battery was flat , I forgot lights on ....
but I had another old battery in trunk so i tried with it but no charge enough to start, anyway i tried reprogram the central locking i did it in 1 and 2 positions and in another the both blink indicators flashed but doors didn't open like in omega. Then we tried to start it with another car , sterter was rolling but car didn't start we tried many times but no start, finally i tried to reprogram the central locking again and after that car started instantly !
so what went wrong or does combo need central programming after flat battery ??
but I had another old battery in trunk so i tried with it but no charge enough to start, anyway i tried reprogram the central locking i did it in 1 and 2 positions and in another the both blink indicators flashed but doors didn't open like in omega. Then we tried to start it with another car , sterter was rolling but car didn't start we tried many times but no start, finally i tried to reprogram the central locking again and after that car started instantly !
so what went wrong or does combo need central programming after flat battery ??
11
Omega General Help / Re: Broken remote or what ?
« on: 25 April 2014, 17:58:36 »
Is this right new remote for me ? In old reads :
28.08.00 433MHz E 02579908 and on other side:
13
5442
01
2 buttons so am I right this is Bosch ??
Brand new in packege reads
GM# 24424723 , 6239034,
GR.104.4861
Is this same remote ?
28.08.00 433MHz E 02579908 and on other side:
13
5442
01
2 buttons so am I right this is Bosch ??
Brand new in packege reads
GM# 24424723 , 6239034,
GR.104.4861
Is this same remote ?
12
Omega General Help / Re: Broken remote or what ?
« on: 22 April 2014, 17:41:26 »Sounds like a dry or broken joint on one of the battery pins to the PCB to me.
Don't look like it and I got 0 ohms from pins and buttons was 0 ohms too...
13
Omega General Help / Re: Broken remote or what ?
« on: 22 April 2014, 08:23:38 »
I have tried with another battery from working Combo's remote no help , Could ther be broken or loose condersator so the charging takes longer time ?
14
Omega General Help / Broken remote or what ?
« on: 22 April 2014, 07:58:06 »
My keys remote stopped working so I replaced new battey but no help.
Problem is that when I push one button the led flashes but if I push another botton after that no led. If I wait about 30 secs and push the led lights again. so can't theach remote because it needs rapid open- close pushes . what would be the problem Martin renewed the buttons less than year ago ?
Omega 2.5 TD facelift 2000....
Problem is that when I push one button the led flashes but if I push another botton after that no led. If I wait about 30 secs and push the led lights again. so can't theach remote because it needs rapid open- close pushes . what would be the problem Martin renewed the buttons less than year ago ?
Omega 2.5 TD facelift 2000....
15
Omega General Help / Re: Locking Wheel Bolts OMG
« on: 14 February 2014, 17:58:40 »
How hard is the nut ?
What if you drill 4mm hole in the middle of nut and then larger hole little by little until nut is gone....?
What if you drill 4mm hole in the middle of nut and then larger hole little by little until nut is gone....?