1
General Discussion Area / Re: Omega Olympics ad on TV .
« on: 10 August 2012, 23:26:44 »
Listen to bigger bang album,Keith Richards sings on it,pretty good to 
- 21 July 2025, 23:03:14
- Welcome, Guest
News:
Welcome to OOF
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Omega General Help / Re: high tickover
« on: 02 March 2009, 19:15:36 »
http://www.omegaowners.com/forum/YaBB.pl?num=1194007453
I used this guide on my 2 litre.
after the cleaning the revs would go up and down.My fault for being heavy handed with the accelerator outer sheath.not enough slack to adjust butterfly.
I used this guide on my 2 litre.
after the cleaning the revs would go up and down.My fault for being heavy handed with the accelerator outer sheath.not enough slack to adjust butterfly.
4
Omega General Help / Brake pad question
« on: 04 August 2008, 23:56:49 »
Have the chance of a free set of front brake pads.
Thing is they are for a 2L w reg Vectra.
Would they be suitable for my miggy?
Thing is they are for a 2L w reg Vectra.
Would they be suitable for my miggy?
5
Omega General Help / Re: Code 93 - 2.0 16v ?
« on: 30 July 2008, 21:34:12 »
camshaft position sensor voltage low poss shorting to earth
94-96 x20xev
94-96 x20xev
6
Omega General Help / Found this on internet
« on: 16 July 2008, 02:02:26 »
Thought maybe it would help some with all the gizmos in their Mig
http://homepage.ntlworld.com/andrew.reynolds983/Manuals/Omega2002Manual.pdf
http://homepage.ntlworld.com/andrew.reynolds983/Manuals/Omega2002Manual.pdf
8
Omega General Help / Re: trouble after rebuild
« on: 30 June 2008, 15:47:27 »
Had this problem after cleaning breathers,throttle.Turned out i was a bitheavy handed with the outer accelarater sheath,not enough slack to adjust the butterfly valve,slackened it off ,adjusted butterfly valve to closed,almost,no probs since.
just a thought
just a thought
9
Omega General Help / Re: Rust under the wheel arches
« on: 08 April 2008, 18:26:14 »
Have been doing the rust around arches and top of door myself,body work repairs are labour intensive and can't afford it.#So am tackling it myself.
Used a wire wheel thingy to get down to bare metal,used Kurust to treat,filled ,sanded and then sprayed base and top coat.
Paint ,filler and rust treatment are pretty cheap,it is just time consuming.
Post b4 and after pic soon,just a bit more to do.
Used a wire wheel thingy to get down to bare metal,used Kurust to treat,filled ,sanded and then sprayed base and top coat.
Paint ,filler and rust treatment are pretty cheap,it is just time consuming.
Post b4 and after pic soon,just a bit more to do.
11
Omega General Help / Re: Can anyone identify this?
« on: 07 March 2008, 12:37:50 »
Could be part of a plastic insert to hold car mat in place.
12
Omega General Help / Re: strange noise
« on: 05 March 2008, 14:42:37 »
These may help if i read post correctly
http://www.omegaowners.com/forum/YaBB.pl?num=1152618876
http://www.omegaowners.com/forum/YaBB.pl?num=1152745540
http://www.omegaowners.com/forum/YaBB.pl?num=1152618876
http://www.omegaowners.com/forum/YaBB.pl?num=1152745540
14
Omega General Help / DBW
« on: 03 March 2008, 22:34:57 »
Just curious.
What is it and how does it work?
What is it and how does it work?
15
Omega General Help / Re: Door window trim rust!
« on: 21 February 2008, 20:10:32 »
Strange this has popped up.Monday i went to stealers an bought n/s rear weather strip (£17)filler,etching primer,primer,top coat and a can of waxoyl.Hope to do the door this weekend.