1
Omega Electrical and Audio Help / Re: aftermarket stereo with bose
« on: 07 June 2008, 20:11:25 »
well it works fine with alpine 
))))
))))
- 24 October 2025, 14:32:38
- Welcome, Guest
News:
Please check the Forum Guidelines at the top of the Newbie section
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
Omega Electrical and Audio Help / Re: aftermarket stereo with bose
« on: 07 June 2008, 19:33:24 »
I have done the same. U dont need to remove anything !!!! All you need to do is find the remote + for bose amp and connect it to the new unit as amp remote. Works fine and sound is briliant !!! Just i would advice not to buy cheap ebay c**p from china. Cos they are using diferent amp for out and on low volume you will hear a bit buzzin from your speakers. i would recomend alpine, sony, kenwood, pioner, jvc. With those works fine !!! Good luck
3
Omega Electrical and Audio Help / Re: Upgrading Elite CD player !!!
« on: 18 May 2008, 13:38:35 »
as I understand there is a solution for this problem Thanks
Thanks
4
Omega Electrical and Audio Help / Re: Upgrading Elite CD player !!!
« on: 17 May 2008, 15:25:20 »
well if just I could make amp working so I think it should convert output from 4 Omh to 2 omh. Just been to my local vauxhall dealer and they havent got a clue. tw...... ! Anyway I am not going to give up that easily. Will have to play with amp cables then
5
Omega Electrical and Audio Help / Re: Upgrading Elite CD player !!!
« on: 17 May 2008, 13:45:01 »
it was philips ccr 2006 cd player. the new unit is alpine but it has the same ISO back socked I bought at Halfords. and there is no sound at all but new unit works fine, i can swich it on and adjust everything just there is no sound. I have cheched the new unit on the other car and it works fine. I think that bose has amp but how can I know now where it is and which cables go to it. its a bit stupid.
6
Omega Electrical and Audio Help / Re: Upgrading Elite CD player !!!
« on: 17 May 2008, 09:15:10 »
what is strange that i have w red cd model and all the wires are diferet. looks like elite have extra cables for amp etc...
7
Omega Electrical and Audio Help / Upgrading Elite CD player !!!
« on: 16 May 2008, 23:39:31 »
Hi i have a problem upgrading my omega elite sound system. It has BOSE sound system and I have removed original CD player. Then I conect new one there is no sound at all. The new unit works but no sound. Anyone knows what might be the problem 
I heard that there is a bose amp somewhere but how to connect new stereo to it >>>
THAnks
I heard that there is a bose amp somewhere but how to connect new stereo to it >>> THAnks
8
Omega General Help / Re: Intermitent not starting
« on: 11 June 2008, 23:12:39 »
Hi, I have the same problem. Just with V6. In the morning it will start without any problems and runs smooth. Later when u switch of the engine it won't start for couple hours. And this started after I have touched camshaft sensor. Before that everything was fine. Just dunno now what to do. Do I have to change that sensor or the problem is in some where else
9
Omega General Help / Re: New Gear box sump?
« on: 01 July 2008, 00:01:32 »
so it is not on the sump??? there about is it then ?
10
Omega General Help / New Gear box sump?
« on: 30 June 2008, 23:41:53 »
Had a bit of oil leak from my gearbox. So I decided to tighten the sump and it worked. No more leak but trying to top up gearbox oil damaged the level bolt coz it got stuck in the sump. Anyway I couldnt undo it. it will turn but not go out. strange. And its not leaking. Any other ways to check the level of oil in the gearbox and top it up or I have to get new sump from the scrap yard?
11
Omega General Help / code 19
« on: 27 June 2008, 11:49:00 »
Just have changed cranck shaft sensor becouse it was cuttin off when hot. And I still have code 19 poping out when doing paperclip test. Will it disapear after some time or not To be honest its not a big problem just can it be something else? And one more thing. doing paperclip test i know code 31 should flash when the engine is off but it gives me only 12 and 19. Any ideas
To be honest its not a big problem just can it be something else? And one more thing. doing paperclip test i know code 31 should flash when the engine is off but it gives me only 12 and 19. Any ideas
12
Omega General Help / Re: Camshaft Position Sensor !
« on: 12 June 2008, 01:00:15 »
Done paper clip test and it came up with 12 and 31. Nothing else.
13
Omega General Help / Camshaft Position Sensor !
« on: 12 June 2008, 00:58:20 »
Hi. I was just cleaning oil on camshaft covers and removed the sensor. After that it wont start. Next day it was ok until i turned the engine off. after couple hour it will start again. I am sure i have installed the sensor as it was. Today mornin started the car, went to work and its dead now. I have checked it makes no sparks, not suplying fuel as well. Does it makes any sense that I have damaged the sensor accidently Or it might be something else???
Or it might be something else???
14
Omega General Help / Re: Low Beam Fld/Vision ???
« on: 08 June 2008, 19:22:27 »
just done it its was front passengers side. Now its ok thanks for help !!! Its very easy to find it !!
its was front passengers side. Now its ok thanks for help !!! Its very easy to find it !!
Pages: [1] 2