Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega Electrical and Audio Help / supercharging

« on: 23 December 2009, 21:40:27 »

hi i have a 3.0 mv6 manual 1999 and im very interested in supercharging it i have found a kit that will fit but it does not include an ecu, i was wondering can the current ecu be remapped to suit the supercharger

2

Omega Electrical and Audio Help / maf sensor

« on: 22 November 2009, 14:32:18 »

i am thinking about building a custom inlet manifold for my 3.0 mv6 but i need to find out if it is possible to put the mass air flow sensor behind the throttle body or can it be removed from the system, can anyone help.

3

Omega Electrical and Audio Help / removing the mass air flow sensor

« on: 24 October 2009, 19:19:48 »

hi i have recently brought an omega 1999 mv6 manual pre-facelift and im thinking about making a custom inlet manifold with 100mm throttle body, but i was wondering is there a way of getting rid of the mas air flow sensor,

p.s if anyone has a lsd for this car i would be very interested thanx.

4

Omega General Help / Re: Alarm fault

« on: 11 July 2011, 18:05:16 »

I have read other posts about the romovel of the power sounder but is it possible do it without the alarm going off

5

Omega General Help / Re: Alarm fault

« on: 11 July 2011, 17:53:55 »

Sorry it is the siren and wen I tried to disconnect it the horn next to it just kept going off, does any one have a clue what to do?

6

Omega General Help / Re: Alarm fault

« on: 11 July 2011, 12:14:05 »

I think it more of a horn

7

Omega General Help / Alarm fault

« on: 11 July 2011, 06:40:32 »

Hi I have recently brought a 52 3.2 omega and the last couple of times I have started it the alarm has gone off. I does not set the hazards off and the only way to stop it is to get out and lock it on the button. Does anyone have an idea what it could be?

8

Omega General Help / 3.2 mv6 mods

« on: 10 July 2011, 15:35:46 »

Hi I have recently brought a 3.2 52 plate black mv6 and I'm lookin at modifying it, I'm looking at putting some 19" snowflake alloys and maybe lowering it but I don't want to make it too bumpy, and also fitting a front splitter but I can't find one that fits the mv6 prodrive bumper. Can anyone help?

9

Omega General Help / Re: LSD

« on: 23 December 2009, 21:46:25 »

the easiest way to test it is to put the car in first give it the beans lift of the cluch and hold it on the foot brake for about 5 seconds keepin the revs above 3000 rpm and the get out and check if there are one or two tyre spin marks on the floor

10

Omega General Help / heater fault

« on: 16 December 2009, 13:29:01 »

i hav reciently brought an omega mv6 1999 and the heater just blows cold air until you get on the motorway, i have driven it around town for 30 minutes and it is still cold.

11

Omega General Help / omega lsd diff

« on: 05 November 2009, 18:05:36 »

hi im interested in a lsd for my omega mv6 3.0 manual and i have found one on ebay http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=230395283633&_trkparms=tab%3DWatching
but the seller doesnt no what it came off, was it only the 3.0 manuals that had a lsd and will there be any ID numbers on it that would tell me.

12

Omega General Help / Re: unkown vibration

« on: 27 October 2009, 17:10:58 »

also will a 2.5 manual prop fit

13

Omega General Help / Re: unkown vibration

« on: 27 October 2009, 15:34:52 »

do u no if the auto prop shaft is the same as a manual one

14

Omega General Help / Re: unkown vibration

« on: 27 October 2009, 15:04:48 »

i have checked everything on the front and its ok but the vibration is not coming throught the stearing wheel it comes through the floor of the car and is pretty harsh

15

Omega General Help / Re: unkown vibration

« on: 27 October 2009, 14:15:53 »

i have had 4 wheel alignment checked but that was spot on, i think i might have to get a second hand prop but im not sure if the auto propshaft will fit or not