Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Omega Electrical and Audio Help / Re: Lamp dangling in space !

« on: 20 January 2007, 22:10:00 »

You dealer is being a idiot. Try another one.  Else, try and old fashioned scrappy, and fill your pockets like Tunnie does  

How true  

I wish I could find a scrappy! None about here at all, tho I did hear of one locally today. Will have to get round and hope for a meega!

hiya there is 1 amber led at the top of your light unit sometimes the led does blow and somtimes its the dry solder on the circuit board .the twist fit bulb in the back that is surpose to light up the bottom half. you can find the same bulbs in vectra light units and in the back of omega and vectra speedo pods from 98 on the speedo pod warning light bulbs are brighter than the standard bulbs you find in the back of headlamp switch units grab your self a load of those if you see any in the scrappys .

2

Omega General Help / Re: 1999 Omega Elite 2962cc.

« on: 29 March 2010, 12:12:44 »

hi i clean my icv with carb cleaner and i also cleaned where the butterflys are so they close propperly

thanks

3

Omega General Help / Re: 1999 Omega Elite 2962cc.

« on: 29 March 2010, 10:14:07 »

hi intresting topic i have the same issue i changed all leads plugs cleaned icv and all breathers are also clean and i still have the same prob the breathers i cleaned where all the ones from that box behind the engine and the black strip on the top of the manifold but my 3.0 still runs rough on idle but clears when u take it above 600 odd revs strange

thanks

4

Omega General Help / engine light issue

« on: 29 March 2010, 17:27:10 »

hi i have a 3.0 mv6 1 more problem  to sort out lol regards to engine light if i disconnect the knock sensors both of them the engine light dont come on but if i disconnect any other sensor the light comes on. im trying to find out why my engine runs lumpy on idle ive covered everything eles breather icv leads plugs so im now looking at sensors has any 1 eles had the same problem i would luv to hear about it

thanks

5

Omega General Help / Re: LEADS AND COIL PACK ISSUE

« on: 29 March 2010, 09:45:33 »

hi just to let you know ive sorted them thanks for all your help

brett

6

Omega General Help / Re: LEADS AND COIL PACK ISSUE

« on: 28 March 2010, 02:31:25 »

thanks for the info guys il sort that tommorow and will post back

thanks

7

Omega General Help / Re: LEADS AND COIL PACK ISSUE

« on: 27 March 2010, 23:23:06 »

lol sorry im just not wiv it today its a mv6 3.0 1999

thanks

8

Omega General Help / LEADS AND COIL PACK ISSUE

« on: 27 March 2010, 22:59:12 »

hi everyone i hope u are all having a good weekend im not lol ive been a noob .i decided to change my plugs and leads and just removed the lot and like a noob i didnt mark what lead goes on to what pin on the coil pack can anyone help me please

i look forward to reciving some replys fingers crossed

9

Omega General Help / Re: Prop Shaft Vibration

« on: 11 February 2010, 22:25:24 »

hi m8 i had the same problem my centre barring rubber was weak "perrished"

10

Omega General Help / Re: Rusty bores

« on: 15 February 2010, 20:39:04 »

hi m8 i had same problem i used very smooth wet and dry i also used a bit of light oil to rub around and everything is good 

11

Omega General Help / Re: Exhaust Studs

« on: 11 February 2010, 22:20:10 »

hi m8 i did what elite pete said if they do shear off like mine did i used small drill bit and worked up a few sizes but once u got the pipes off there will be part stud hanging out i had the flattern them with a grinder being carefull just to get them flat so u can drill easier mine went back to gether no blowing at all good luck .

12

Omega General Help / Re: Oxygen sensor

« on: 09 February 2010, 18:35:43 »

hi ive changed that cam sensor restarted car and light came on again done a retest with paper clip and still got same 2 numbers i dont understand it at all ive recently changed the matrix i cant see that having anything to do with this problem ?

13

Omega General Help / Re: Oxygen sensor

« on: 08 February 2010, 21:04:03 »

hi ive just gone out and disconnected that air mass metre and done test and still got those 2 same numbers 38 and 91

thanks

14

Omega General Help / Re: Oxygen sensor

« on: 08 February 2010, 20:22:59 »

ok cool i will disconnect it and do another test and i will reply tommorow night  with what codes it comes up with thanks for your help be back soon

brett

15

Omega General Help / Re: Oxygen sensor

« on: 08 February 2010, 20:08:11 »

hi sorry to ask what is a maf ?