1
Omega Electrical and Audio Help / Re: immobiliser problem
« on: 31 July 2010, 12:43:22 »
thanks for the pic my chip is missing can they be replaced
- 24 October 2025, 16:44:58
- Welcome, Guest
News:
Search the maintenance guides for answers to 99.999% of Omega questions
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
Omega Electrical and Audio Help / immobiliser problem
« on: 27 July 2010, 20:32:58 »
got a fault with one of my keys it starts the engine but stops again immobiliser light flashing micro switches working can these be repaired?
3
Omega Electrical and Audio Help / Re: cdr 2005
« on: 02 March 2010, 22:20:49 »
yes at first it was the wrong code i found the right one and got it entered eventually all is well now with the radio but still have another problem
4
Omega Electrical and Audio Help / cdr 2005
« on: 28 February 2010, 16:25:02 »
i have a problem with my radio battery been of for a while now when i try to enter the code by pressing the as button and pressing the on switch i getthe message 7 safe and cant go any further
5
Omega General Help / Re: engine wont start
« on: 23 July 2010, 22:00:41 »
hello again i have fitted the cam sensor from the original engine running better now took it for a run did 18 miles management light still on still no codes left it for about half an hour restarted it light has gone out been for a run runs good now light has not come back on
6
Omega General Help / Re: engine wont start
« on: 21 July 2010, 17:36:21 »
well i have never heard of ov connections bofore now
7
Omega General Help / Re: engine wont start
« on: 20 July 2010, 22:07:00 »
it is running now but the light is staying on my code reader does not pick up any codes still not running to great whenit starts i have to let it idle before it will take throttle drove it a few hundred yards running hotter than before engine change
8
Omega General Help / Re: engine wont start
« on: 20 July 2010, 20:53:19 »
if the cam sensor was faulty i thought it would not start at all if i crank it over enough it will eventually start and as long as i keep revs on it it runs but a bit rough will idle after awhile but the light staying on
9
Omega General Help / Re: engine wont start
« on: 20 July 2010, 20:16:38 »
if you mean earth connections then they are good i did manage to get it run for a little while throttle working ok but a little rough with management light on switched it of tried to find codes none stored tried to restart it will start up to 1000 rpm then dies does not respond to throttle
10
Omega General Help / Re: engine wont start
« on: 20 July 2010, 19:23:54 »
everything seems to be ok i cant find anything loose when i removed the engine i just moved the loom to the other side of the engine bay it was not removed
11
Omega General Help / Re: engine wont start
« on: 20 July 2010, 19:15:02 »
i can try fitting the set that came with the replacement engine as i knew the original ones were ok untill the engine blew up i thought i would use them
12
Omega General Help / Re: engine wont start
« on: 20 July 2010, 19:09:26 »
the injectors are from the original engine but i did get a set with the replacement engine
13
Omega General Help / Re: engine wont start
« on: 20 July 2010, 18:55:58 »
starting to seem like it might be a fuel problem maybe the sensors are working
14
Omega General Help / Re: engine wont start
« on: 20 July 2010, 18:07:36 »
i tried putting some fuel down the throttle body and the engine did try to run but very rough but got codes p0240 p0204 p0202 does this help anybody
15
Omega General Help / Re: engine wont start
« on: 19 July 2010, 22:45:05 »
spanner light stays on while abs etc go out spanner light goes out when engine is cranking
Pages: [1] 2