1
Omega General Help / Re: v6 omega
« on: 24 December 2009, 11:09:59 »
man those two pipe look really hard to get to i will give it a go today in the cold and stick a hose pipe down one end .
- 15 May 2025, 10:58:24
- Welcome, Guest
News:
Welcome to OOF
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Omega General Help / Re: v6 omega
« on: 24 December 2009, 10:25:22 »
how do i un block the matrixwhat pipes do i pull off and how do i know when its flushed
3
Omega General Help / Re: v6 omega
« on: 24 December 2009, 09:25:39 »
well my oil cooler went down so i fixed that but i dont get hot air and when i took the two pipes off two clean tham i stuck a airline down the black electric thing and the little turbine blades dont spin is that why i dont get hot air
4
Omega General Help / v6 omega
« on: 24 December 2009, 09:13:56 »
hi can anyone tell me what is that black thing under the the water header tank it has two pipes going to it and it looks like a coil with a connector behind it . 
5
Omega General Help / OIL COOLER BEEN CHANGED STILL PROB
« on: 18 December 2009, 11:22:53 »
can anyone help me pls iv changed the oil cooler but it was that bad the rad is complete blocked and its just boiling over the rad is stone cold and the car gets to temp but no hot air . if i put the cap on its starts to over heat any idea what to do next do i take the rad out and un block it .And is there anyway i can un block the matrix thanks any help pls.sorry its a v6 
6
Omega General Help / the best way to clean the system after an oil cool
« on: 14 December 2009, 21:18:03 »
any idea the best way to clean the system out after oil cooler change there is brown stuff ever where even in the header tank and where the oil cooler goes pls any idea 
7
Omega General Help / oil cooler
« on: 14 December 2009, 10:19:12 »
hi once again just got my new oil cooler but was wondering what gasket and what o-ring to order for my job on my 2.6 v6 and has anyone got any part number and do i need any sealant for the job . Also can anyone tell me how long will it take to do the job thank.
8
Omega General Help / v omega oil cooler
« on: 06 December 2009, 10:41:41 »
can anyone tell me how much a oil cooler is pls and where is the best plase to get one i need to change mine .
9
Omega General Help / Re: v omega v6
« on: 02 December 2009, 00:47:10 »
thanks guys for all your help
10
Omega General Help / v omega v6
« on: 01 December 2009, 21:54:56 »
hi there first thing is im new to this site so i will say hello to everone 
Now then can anyone help me iv just had my omega for 6 weeks and i think the head gasket has gone its a 2.6 v6 on a y reg and has only got 74000 miles .the problem is the coolant has brown guee water the local garage says its the head gasket and said to do the job around 1300 quid well i nearly past out can any one shed any light pls...
Now then can anyone help me iv just had my omega for 6 weeks and i think the head gasket has gone its a 2.6 v6 on a y reg and has only got 74000 miles .the problem is the coolant has brown guee water the local garage says its the head gasket and said to do the job around 1300 quid well i nearly past out can any one shed any light pls...
Pages: [1]