1
Omega Electrical and Audio Help / Re: Tech 2
« on: 12 September 2010, 17:35:26 »
The codes are 0150,0155 sensor has been replaced car has been to local garage twice and is stumped.always comes back on two days later.
- 22 July 2025, 23:08:04
- Welcome, Guest
News:
Please check the Forum Guidelines at the top of the Newbie section
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
Omega Electrical and Audio Help / Tech 2
« on: 12 September 2010, 16:48:05 »
Hi,is there a tech 2 person somewhere close to me that could plug in for live data as eml light will not go off.Thanks in advance 
3
Omega Electrical and Audio Help / Re: car alarm
« on: 01 September 2010, 07:00:52 »
Hi all , i have now disconected the bonnet switch, i set the alarm for the night at about 6pm and was woken with alarm going off about 7 hrs later is there a next step i can try thank you. :-?
4
Omega Electrical and Audio Help / Re: car alarm
« on: 16 August 2010, 20:43:35 »
hi,if i disconnect the bonnet switch will the alarm still set or does it need to be connected thank you. 
5
Omega Electrical and Audio Help / car alarm
« on: 16 August 2010, 20:32:56 »
HI,
i have a slight problem with my 2001 2.6 v6 manual when i come back from a drive and lock the car the alarm goes off about 20-30mins after setting it and when i set the alarm the secound time its o.k but it sometimes goes off early hours in the morning and sometimes it does not go off if anybody has and idea i will be greatfull.
i have a slight problem with my 2001 2.6 v6 manual when i come back from a drive and lock the car the alarm goes off about 20-30mins after setting it and when i set the alarm the secound time its o.k but it sometimes goes off early hours in the morning and sometimes it does not go off if anybody has and idea i will be greatfull.
6
Omega General Help / Re: stem oil seals
« on: 11 September 2010, 22:51:16 »
I have checked the wires on the black connector under the car and are o.k all 4 sensors tested the same when it was at the garage i am a bit stumped with electrical as i am more machanical, where would i start looking code faults are 0150,0155 bank 2 sensor 1 even when i have changed the sensor Thank you,
7
Omega General Help / Re: stem oil seals
« on: 11 September 2010, 22:36:07 »
Does anyone know how long and what tools i need to change the valve stem oil seals as i will have to do to fix the problem of the eml light comming on.Thank you
8
Omega General Help / Re: stem oil seals
« on: 11 September 2010, 18:34:17 »
Would this smoke be the cause of the eml comming on.
9
Omega General Help / Re: stem oil seals
« on: 11 September 2010, 18:27:19 »
Thanks for that i do not know what else it could be as all sensors have been tested with no faults , so valve stems it is.
10
Omega General Help / stem oil seals
« on: 11 September 2010, 17:52:47 »
Hi everyone,
my eml light keeps comming on >:(and fault codes keep pointing to bank 2 sensor 1 even thou i have changed one sensor and changed the others around 2 days later and light is on again. When the car has sat for a while and i start it up a cloud of gray smoke comes out the back end can this set off the eml light it only smokes on start up. If so is it the valve stem oil seals.Thank you for help in advance.
my eml light keeps comming on >:(and fault codes keep pointing to bank 2 sensor 1 even thou i have changed one sensor and changed the others around 2 days later and light is on again. When the car has sat for a while and i start it up a cloud of gray smoke comes out the back end can this set off the eml light it only smokes on start up. If so is it the valve stem oil seals.Thank you for help in advance.
11
Omega General Help / Re: Oil in water, changing oil cooler. Got a question.
« on: 05 September 2010, 20:05:53 »
i had the same problem with my 2.6 v6 2001 omega i brought the car with oil in water and i changed the oil cooler only had very little rust on it but had no dout i changed the right part after having advise on the problem by the helpfull people on the forum. This was only a couple of months ago flushed the system about 6 times and started to come clear the other problem was the fans would not kick in when the engine got hot and started to bubble it seamed somewhere had a airlock in the water i managed to clear it by taken the car out for a spin as would not clear on idle hope it helps
12
Omega General Help / Re: fault codes
« on: 05 September 2010, 10:47:06 »
Thanks mate that garage will be seeing me on monday afterall these sensors are not cheap 
13
Omega General Help / Re: fault codes
« on: 04 September 2010, 21:25:27 »
Thank you for the reply i have today had the car on ramps and checked the wiring on both sensors and seam to be o.k a few weeks ago i had a sensor replaced as managment light was on then,did not find out which one until today it was the one after cat on passenger side . There was no leak on manifold so does this mean i have got to replace the the sensor before the cat , thanks for the help
14
Omega General Help / fault codes
« on: 03 September 2010, 12:18:32 »
Hi everyone,
my managment light has come on and i have done the peddle test to get the fault codes 0155 0150 and 0159 i have looked at fault codes listed and believe it to be bank 2 sensor 1 but can not find one for 0159 . does anyone know which sensor this is so i can change the correct sensor any help will be greatfully recieved as always. :-?
my managment light has come on and i have done the peddle test to get the fault codes 0155 0150 and 0159 i have looked at fault codes listed and believe it to be bank 2 sensor 1 but can not find one for 0159 . does anyone know which sensor this is so i can change the correct sensor any help will be greatfully recieved as always. :-?
15
Omega General Help / code reader
« on: 19 March 2010, 12:40:59 »
Hi,does anyone live in the lincolnshire area with a code reader to clear my faults on a 2001 2.6 omega,Thank you
Pages: [1] 2