1
Omega General Help / Re: Cambelt on a V6
« on: 22 July 2010, 19:10:24 »
My cam belt had done 70k and was over 5 years old when it was changed but it not worth the risk, its £200+ well spent. 
- 23 July 2025, 07:11:17
- Welcome, Guest
News:
Please play nicely. No one wants to listen/read a keyboard warriors rants....
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Newbie Welcome Area / Hello all
« on: 09 June 2010, 13:42:25 »
I am a complete newbie to forums.
Have had my Omega for 4 years now its been off the road for a year, its had a rest in the garage been started and moved weekly so hoping all will be well when it goes for MOT next Wednesday.
Regards to all
Kindadraws.
Have had my Omega for 4 years now its been off the road for a year, its had a rest in the garage been started and moved weekly so hoping all will be well when it goes for MOT next Wednesday.
Regards to all
Kindadraws.
3
Newbie Welcome Area / Re: Key Trouble
« on: 10 June 2010, 09:06:37 »
from one newbie to another hello.
And good luck with your key probs.
And good luck with your key probs.
5
General Car Chat / Re: windscreen companies.
« on: 08 July 2010, 14:26:27 »
It's worth noting that although Insurance companies say that a winscreen repair/replacement will not affect your ncb's, a note is made on your record that you have claimed. More Than show this as a claim on your proof of no claims bouns when you re new.
6
General Discussion Area / Re: Big Thank You to Elite Pete
« on: 22 July 2010, 16:35:09 »
Must be that new Shell "Fuel saver Fuel" I filled up with. Save 1 ltr in every 50ltrs?
Has always been good on a run and my granddad driving at 70 mph, its round town or in traffic that it goes down to the mid to low 20s.
Has always been good on a run and my granddad driving at 70 mph, its round town or in traffic that it goes down to the mid to low 20s.
8
General Discussion Area / Re: Big Thank You to Elite Pete
« on: 22 July 2010, 16:17:18 »
I spent 5 hours there it was raining very hard don't know the area just put in the post code then drove to hotel near Pete. 
9
General Discussion Area / Re: Big Thank You to Elite Pete
« on: 22 July 2010, 16:12:11 »
Anywhere in the UK, Freelance Draughtsman have to go where the work is.
10
General Discussion Area / Re: Big Thank You to Elite Pete
« on: 22 July 2010, 16:05:15 »
Project Managment/AutoCAD, not much to tell sometimes have to meet clients/contractors at their site.
11
General Discussion Area / Re: Big Thank You to Elite Pete
« on: 22 July 2010, 15:59:17 »
I did try to get local help unfortunately it didn't work out.
I had a job to look at in Liverpool and combined the 2.
Drove up with my fingers crossed cam belt last changed 5years and 70k ago, having said that it didn't look to bad, tensioners still seamed ok I wont leave it that long again.
Pete was great very entertaining and done a good job.
I had a job to look at in Liverpool and combined the 2.
Drove up with my fingers crossed cam belt last changed 5years and 70k ago, having said that it didn't look to bad, tensioners still seamed ok I wont leave it that long again.
Pete was great very entertaining and done a good job.
12
General Discussion Area / Big Thank You to Elite Pete
« on: 22 July 2010, 09:25:00 »
Lovely Job Pete,
Cam Belt, Water Pump, Aux Belt, Breathers Cleaned & Oil/filter Change.
Replacing the Vac pipe to the rams, chewed by rats has made a difference.
The old omega managed 36.8mpg over a 460 mile round trip.
Kindadraws.
Cam Belt, Water Pump, Aux Belt, Breathers Cleaned & Oil/filter Change.
Replacing the Vac pipe to the rams, chewed by rats has made a difference.
The old omega managed 36.8mpg over a 460 mile round trip.
Kindadraws.
13
General Discussion Area / Re: Insurance renewal
« on: 08 July 2010, 18:00:56 »
Full com with More Than £370, 12K miles, business use and named driver full protected no claims.
14
General Discussion Area / Re: USERNAMES
« on: 07 July 2010, 14:07:06 »
I spend my day drawing steel structures on a 3D CAD but cannot draw free hand so, I only kindadraw.
Pages: [1]