Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1]   Go Down

Author Topic: Tensioner pointer confusion.  (Read 1168 times)

0 Members and 1 Guest are viewing this topic.

Bent valve

  • Senior Member
  • ****
  • Offline Offline
  • 0
  • Posts: 950
    • View Profile
Tensioner pointer confusion.
« on: 29 March 2009, 23:46:05 »

 I have fitted a new belt and tensioner kit to my 3.0ltr v6 today, and I am confused as to what the final position of the tensioner pointer should be.
  after initialy setting the pointer to align with the right hand side of the lug, then turning  the engine over 2 revolutions, and locking the crank at tdc. the pointer swings down anti clock wise and aligns with the scribe mark on the lug. is this correct? it is vague on the cambelt dvd as to where the final position should be. Haynes manual does not say either. skf say it should be between 2-4 mm beyond scribe mark after 10 rotations of the engine. the Geoff and Pete how to says both marks should be aligned after 2 rotations.
Anyone know for sure?
Logged

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 106843
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: Tensioner pointer confusion.
« Reply #1 on: 30 March 2009, 08:03:49 »

should be on left edge if new belt - marking for used belt

retension, then 2 more revs, then check again, and repeat, each time ensure the pulley marking line up with timing tool, and tensioner correct
Logged
Grumpy old man

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 33983
  • Git!
    • View Profile
Re: Tensioner pointer confusion.
« Reply #2 on: 30 March 2009, 08:23:47 »

Upper edge of the marker for a new belt....aligned with the centre scribe for a used belt
« Last Edit: 30 March 2009, 08:23:59 by Mark »
Logged

jonathanh

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • coventry
  • Posts: 1199
    • View Profile
Re: Tensioner pointer confusion.
« Reply #3 on: 30 March 2009, 09:04:10 »

the logic is that setting to the upper edge gives a slightly higher tension on the belt when new.  when it settles in then you'd expect the belt to fit more snugly, meaning it the tensioner backs off a bit.

I recently rechecked my belt after 7k miles:  pointer was on upper edge when fitted, it is now closer to the mid marker
Logged
parking near Birmingham airport for members with +250 posts.  PM for info

Bent valve

  • Senior Member
  • ****
  • Offline Offline
  • 0
  • Posts: 950
    • View Profile
Re: Tensioner pointer confusion.
« Reply #4 on: 31 March 2009, 18:21:45 »

Thanks for the advice chaps, I set it to the upper mark and finally got it running last night, after a top end rebuild which involved replacing numerous bent valves and guides ect.

My Knuckles are skinned raw, my backs aching, and my wallet is empty,
but it was all worth it because it runs like a swiss watch :y
Logged

ians

  • Omega Baron
  • *****
  • Offline Offline
  • Reading
  • Posts: 3394
    • View Profile
Re: Tensioner pointer confusion.
« Reply #5 on: 31 March 2009, 18:45:06 »

Quote
Thanks for the advice chaps, I set it to the upper mark and finally got it running last night, after a top end rebuild which involved replacing numerous bent valves and guides ect.

My Knuckles are skinned raw, my backs aching, and my wallet is empty,
but it was all worth it because it runs like a swiss watch :y

luvley jubbly - well done :y
Logged

vauxmad

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Oswestry, Shropshire
  • Posts: 235
    • View Profile
Re: Tensioner pointer confusion.
« Reply #6 on: 31 March 2009, 20:15:13 »

its all worth it for the sense of achievement i the end
Logged
Pages: [1]   Go Up
 

Page created in 0.058 seconds with 18 queries.