Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Search the maintenance guides for answers to 99.999% of Omega questions

Pages: [1]   Go Down

Author Topic: torque settings  (Read 720 times)

0 Members and 1 Guest are viewing this topic.

ianboyo

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Somerset
  • Posts: 95
    • View Profile
torque settings
« on: 10 February 2011, 19:30:50 »
hi is there a thread on the torque setting for all the engine componants for v6 can anyone help thank you
 :y
Logged

PhilRich

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • A bit further North of the Back of Beyond!
  • Posts: 10338
    • Mk 2 Volvo V70
    • View Profile
Re: torque settings
« Reply #1 on: 10 February 2011, 19:35:21 »
Quote
hi is there a thread on the torque setting for all the engine componants for v6 can anyone help thank you
 :y




Here you go mate  :y

http://www.omegaowners.com/forum/YaBB.pl?num=1156365122
Logged
If it ain't broke keep fixing it 'til it is!

ianboyo

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Somerset
  • Posts: 95
    • View Profile
Re: torque settings
« Reply #2 on: 10 February 2011, 19:46:08 »
thanks for the settings  :y
Logged

PhilRich

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • A bit further North of the Back of Beyond!
  • Posts: 10338
    • Mk 2 Volvo V70
    • View Profile
Re: torque settings
« Reply #3 on: 10 February 2011, 19:53:04 »
Quote
thanks for the settings  :y




I was only the 'Gopher', the Thanks go to Mr Marks DTM Calib who very kindly did the hard bit! :y
Logged
If it ain't broke keep fixing it 'til it is!

Andy H

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Auckland
  • Posts: 5532
    • Mazda MPV
    • View Profile
Re: torque settings
« Reply #4 on: 10 February 2011, 21:23:54 »
Just curious

What do notes 1,2,3,4,5 & 6 say?

Is it something important..............?
Logged
"Deja Moo - The feeling that you've heard this bull somewhere before."

Entwood

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • North Wiltshire
  • Posts: 19566
  • My Old 3.2 V6 Elite (LPG)
    • Audi A6 Allroad 3.0 DTI
    • View Profile
Re: torque settings
« Reply #5 on: 10 February 2011, 21:30:06 »
The notes are :

1) Use new bolts.
2) Insert bolts with bolt locking compound (red).
3) Use new nuts.
4) Clean thread and insert bolts with bolt locking compound (red).
5) Use new copper seal rings.
6) When re-using oxygen sensor, coat thread with special grease (black).
7) Tightening to 10 Nm is performed after 10 minutes for the old version (without additional bore) and only after assembly of the complete toothed belt drive for the newer version.
8) Clean thread of fastening bolts and insert with bolt locking compound (red).
9) Tightening to 20 Nm is only performed after installation of the lower alternator fastening bolt.
10) Before assembly, coat thread of screw-on port with assembly paste (white).
11) In three stages of 90° each.
12) Retightening not required




Perhaps these need adding to the post in the guide ??  or is my list in TIS different to the one Mark used ??
« Last Edit: 10 February 2011, 21:31:08 by entwood »
Logged

Ploppy

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Norfolk
  • Posts: 738
    • View Profile
Re: torque settings
« Reply #6 on: 11 February 2011, 05:55:05 »
Just wondered if anyone had the torque settings for spark plugs, oil sump plug, oil filter , rear brake discs/ calipers and wheel bolts for the 3.2 V6?

Thanks

Ploppy :y :y
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.06 seconds with 21 queries.