Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1]   Go Down

Author Topic: CCRT700 Adding Sub  (Read 2770 times)

0 Members and 1 Guest are viewing this topic.

Goonybird

  • Junior Member
  • **
  • Offline Offline
  • Northampton
  • Posts: 110
  • Shouldn't have gone to Specsavers
    • View Profile
CCRT700 Adding Sub
« on: 22 March 2009, 21:03:06 »
Hi,
I have a 99T 2.5CDX with the CCRT700 HU and Blaupunkt 6CD in boot. I am quite happy to keep this unit.
Could someone advise best way to get a audio feed to an amp and sub in the boot. I have previous experience with car audio so wiring is not an issue.
What I do need to know,
Is there a pre-amp out on the multi plug at the back of the unit.
Is the car pre-wired already for the Bose amps?
Or, do I have to take a rear speaker feed into the amp. (not my favorite way)
many thanks
Steffi
Logged
Have owned: Opel Manta A 1900 Auto Berlinetta, Opel Manta B 2.0 Auto Berlinetta, Vx Royale Coupe 2.8 Auto, various non Vx, Skoda Superb 130tdi currently Omega 2.5CDX - now Octavia vRS WRC

Dave DND

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • DND Services Ltd
  • Posts: 4216
    • Paignton, Devon
    • View Profile
    • DND Services Ltd
Re: CCRT700 Adding Sub
« Reply #1 on: 22 March 2009, 23:08:45 »
Quote
Hi,
I have a 99T 2.5CDX with the CCRT700 HU and Blaupunkt 6CD in boot. I am quite happy to keep this unit.
Could someone advise best way to get a audio feed to an amp and sub in the boot. I have previous experience with car audio so wiring is not an issue.
What I do need to know,
Is there a pre-amp out on the multi plug at the back of the unit.
Is the car pre-wired already for the Bose amps?
Or, do I have to take a rear speaker feed into the amp. (not my favorite way)
many thanks
Steffi

The BOSE output levels are not the same as standard RCA levels as required by your Bass amp.

Best way by far in this instance, (and I accept your hesitation), is to take a direct feed from the speakers via a high level convertor.

 ;)
Logged
Radio & Decoding Technician
In Car Audio Service Department
www.dndservices.co.uk

Phil B

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • South Wales
  • Posts: 237
    • View Profile
Re: CCRT700 Adding Sub
« Reply #2 on: 22 March 2009, 23:32:11 »
I just did this to my CD500, using one of these http://cpc.farnell.com/_/b070a/car-amplifier-impedance-matching/dp/CP03284?_requestid=535937

I snipped the bullet connectors off and extended the input cables so I could mount the unit behind the glove box, and spliced them in to the front speaker outputs behind the stereo. Solder them in proper and use shrink wrap tubing!

Then I used a female-female rca adaptor to connect it to a stereo RCA cable and ran it to the boot, along with power from the battery and signal feed to turn the amp on spliced into the power antenna line from the stereo.

Took an afternoon, hardest thing being drilling through the bulkhead and fitting a new grommet for the heavy guage power cable, but even this was ok. Sounds much better now!
Logged

Christian

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Shropshire
  • Posts: 611
    • View Profile
Re: CCRT700 Adding Sub
« Reply #3 on: 23 March 2009, 06:21:45 »
Again yes hi level input and then through a line driver imo!

« Last Edit: 23 March 2009, 12:31:34 by Christian »
Logged
Nope i dont doo Sheep!

Goonybird

  • Junior Member
  • **
  • Offline Offline
  • Northampton
  • Posts: 110
  • Shouldn't have gone to Specsavers
    • View Profile
Re: CCRT700 Adding Sub
« Reply #4 on: 23 March 2009, 20:07:39 »
Quote " The BOSE output levels are not the same as standard RCA levels as required by your Bass amp.

Best way by far in this instance, (and I accept your hesitation), is to take a direct feed from the speakers via a high level convertor."

Thanks for the replies.

Where are the outputs for the Bose amp?
Also any info/details of the output levels / output impedence. I may consider making a buffer amplifier. Be a bit of fun.... :)

stef
« Last Edit: 23 March 2009, 20:08:32 by goonybird »
Logged
Have owned: Opel Manta A 1900 Auto Berlinetta, Opel Manta B 2.0 Auto Berlinetta, Vx Royale Coupe 2.8 Auto, various non Vx, Skoda Superb 130tdi currently Omega 2.5CDX - now Octavia vRS WRC

miniator

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Northern Ireland
  • Posts: 420
    • View Profile
    • My YouTube Channel
Re: CCRT700 Adding Sub
« Reply #5 on: 24 March 2009, 11:48:10 »
Quote
I just did this to my CD500, using one of these http://cpc.farnell.com/_/b070a/car-amplifier-impedance-matching/dp/CP03284?_requestid=535937

I snipped the bullet connectors off and extended the input cables so I could mount the unit behind the glove box, and spliced them in to the front speaker outputs behind the stereo. Solder them in proper and use shrink wrap tubing!

Then I used a female-female rca adaptor to connect it to a stereo RCA cable and ran it to the boot, along with power from the battery and signal feed to turn the amp on spliced into the power antenna line from the stereo.

Took an afternoon, hardest thing being drilling through the bulkhead and fitting a new grommet for the heavy guage power cable, but even this was ok. Sounds much better now!

would this work for a facelift with an NCDC2013?
Logged
Omega Wanted: Facelift, 3.0/3.2, Elite/MV6, Charcoal Interior, W.H.Y.

Dave DND

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • DND Services Ltd
  • Posts: 4216
    • Paignton, Devon
    • View Profile
    • DND Services Ltd
Re: CCRT700 Adding Sub
« Reply #6 on: 24 March 2009, 12:18:23 »
Quote
Quote
I just did this to my CD500, using one of these http://cpc.farnell.com/_/b070a/car-amplifier-impedance-matching/dp/CP03284?_requestid=535937

I snipped the bullet connectors off and extended the input cables so I could mount the unit behind the glove box, and spliced them in to the front speaker outputs behind the stereo. Solder them in proper and use shrink wrap tubing!

Then I used a female-female rca adaptor to connect it to a stereo RCA cable and ran it to the boot, along with power from the battery and signal feed to turn the amp on spliced into the power antenna line from the stereo.

Took an afternoon, hardest thing being drilling through the bulkhead and fitting a new grommet for the heavy guage power cable, but even this was ok. Sounds much better now!

would this work for a facelift with an NCDC2013?

This method of using a high level convertor on the speaker outputs should work with 99.9% of stereos that are under 25 watts per channel. If the stereo is of a higher power (unlikely to be OEM), then a higher power converter is required.
Logged
Radio & Decoding Technician
In Car Audio Service Department
www.dndservices.co.uk

miniator

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Northern Ireland
  • Posts: 420
    • View Profile
    • My YouTube Channel
Re: CCRT700 Adding Sub
« Reply #7 on: 24 March 2009, 15:35:47 »
Quote
Quote
Quote
I just did this to my CD500, using one of these http://cpc.farnell.com/_/b070a/car-amplifier-impedance-matching/dp/CP03284?_requestid=535937

I snipped the bullet connectors off and extended the input cables so I could mount the unit behind the glove box, and spliced them in to the front speaker outputs behind the stereo. Solder them in proper and use shrink wrap tubing!

Then I used a female-female rca adaptor to connect it to a stereo RCA cable and ran it to the boot, along with power from the battery and signal feed to turn the amp on spliced into the power antenna line from the stereo.

Took an afternoon, hardest thing being drilling through the bulkhead and fitting a new grommet for the heavy guage power cable, but even this was ok. Sounds much better now!

would this work for a facelift with an NCDC2013?

This method of using a high level convertor on the speaker outputs should work with 99.9% of stereos that are under 25 watts per channel. If the stereo is of a higher power (unlikely to be OEM), then a higher power converter is required.

The NCDC 2013 is the OEM Siemens unit, but how would i confirm that is a 25w/ch??
Logged
Omega Wanted: Facelift, 3.0/3.2, Elite/MV6, Charcoal Interior, W.H.Y.

Dave DND

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • DND Services Ltd
  • Posts: 4216
    • Paignton, Devon
    • View Profile
    • DND Services Ltd
Re: CCRT700 Adding Sub
« Reply #8 on: 24 March 2009, 16:11:51 »
Quote
Quote
Quote
Quote
I just did this to my CD500, using one of these http://cpc.farnell.com/_/b070a/car-amplifier-impedance-matching/dp/CP03284?_requestid=535937

I snipped the bullet connectors off and extended the input cables so I could mount the unit behind the glove box, and spliced them in to the front speaker outputs behind the stereo. Solder them in proper and use shrink wrap tubing!

Then I used a female-female rca adaptor to connect it to a stereo RCA cable and ran it to the boot, along with power from the battery and signal feed to turn the amp on spliced into the power antenna line from the stereo.

Took an afternoon, hardest thing being drilling through the bulkhead and fitting a new grommet for the heavy guage power cable, but even this was ok. Sounds much better now!

would this work for a facelift with an NCDC2013?

This method of using a high level convertor on the speaker outputs should work with 99.9% of stereos that are under 25 watts per channel. If the stereo is of a higher power (unlikely to be OEM), then a higher power converter is required.

The NCDC 2013 is the OEM Siemens unit, but how would i confirm that is a 25w/ch??

From memory, its only about 15W per channel - you should be fine
Logged
Radio & Decoding Technician
In Car Audio Service Department
www.dndservices.co.uk

miniator

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Northern Ireland
  • Posts: 420
    • View Profile
    • My YouTube Channel
Re: CCRT700 Adding Sub
« Reply #9 on: 24 March 2009, 18:11:53 »
Thanks very much dave!

When i have your attention?! is there a better way of connecting up an ipod to the NCDC 2013 than using an itrip?
Logged
Omega Wanted: Facelift, 3.0/3.2, Elite/MV6, Charcoal Interior, W.H.Y.

Dave DND

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • DND Services Ltd
  • Posts: 4216
    • Paignton, Devon
    • View Profile
    • DND Services Ltd
Re: CCRT700 Adding Sub
« Reply #10 on: 24 March 2009, 19:09:04 »
Quote
Thanks very much dave!

When i have your attention?! is there a better way of connecting up an ipod to the NCDC 2013 than using an itrip?

Not familiar with the iTrip - sorry.

NCDXXX units are not the easiest to connect iPods to though.
Logged
Radio & Decoding Technician
In Car Audio Service Department
www.dndservices.co.uk

miniator

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Northern Ireland
  • Posts: 420
    • View Profile
    • My YouTube Channel
Re: CCRT700 Adding Sub
« Reply #11 on: 24 March 2009, 21:19:39 »
Griffin iTrip - it produces an FM signal through which the ipod plays. tune radio in, hey presto. problem is the quality is poor.

what are my options if any for the NCDC?
Logged
Omega Wanted: Facelift, 3.0/3.2, Elite/MV6, Charcoal Interior, W.H.Y.

Dave DND

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • DND Services Ltd
  • Posts: 4216
    • Paignton, Devon
    • View Profile
    • DND Services Ltd
Re: CCRT700 Adding Sub
« Reply #12 on: 24 March 2009, 22:47:04 »
FM Modulator is the only way - we use these ones and have found them to be the best around

http://ice.dndservices.co.uk/shop_show_item.php/ST/modulator/IID/2947/PAGE/shop_search_index.php
Logged
Radio & Decoding Technician
In Car Audio Service Department
www.dndservices.co.uk
Pages: [1]   Go Up
« previous next »
 

Page created in 0.012 seconds with 17 queries.