Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1]   Go Down

Author Topic: heater vent dial illumination ? build gone or is it just me ?  (Read 1367 times)

0 Members and 1 Guest are viewing this topic.

DrAndyB

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Neston / Cheshire
  • Posts: 992
    • 2.5 V6 CDX Manual (MFL)
    • View Profile

Hi,

I noticed today on way home in the dark that the illuminated heater vent dials ( for the '0' for off and '1' for on !) don't appear illuminated ?

The passenger one was illuminated and shining nicely at me  :y, but the two vents in the centre, and the drivers one were :'(, were both distinctly black with no visibility of the illuminated 'O' and '1' which was evident on the passenger one.

Couple of blown dash bulbs ????

How easy are they to replace and where best place to get them from ?

Cheers in advance.

Andy.
Logged

05omegav6

  • Guest
Re: heater vent dial illumination ? build gone or is it just me ?
« Reply #1 on: 19 December 2013, 21:10:22 »

Middle one is a two minute job, right hand one simply pop the end panel off the dash and it's right there :y

Helfrods, Vauxhall or local factors should all be able to sell you a suitable bulb or two :y
Logged

DrAndyB

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Neston / Cheshire
  • Posts: 992
    • 2.5 V6 CDX Manual (MFL)
    • View Profile
Re: heater vent dial illumination ? build gone or is it just me ?
« Reply #2 on: 19 December 2013, 23:12:35 »

 :y thanks  :y

Any pics or best way to do the middle ones ?  Not quite sure from inspection how it comes off to reveal tne bulbs.  ???

Assume there would two bulbs here and single for the drivers ?

Andy.

Logged

05omegav6

  • Guest
Re: heater vent dial illumination ? build gone or is it just me ?
« Reply #3 on: 19 December 2013, 23:37:26 »

Only one bulb :y

To access move both wheels to O then point both vents all the way up or down. Use a modest flat bladed screwdriver and insert between the vents and the centre part. Vents should pop out, then simply undo the two screws and pull the vent assembly out. Bulb holder sits at the top in the centre, removal is easier to do than explain...

How to is covered under Clocks or Instrument Cluster removal in the guides :y
Logged

DrAndyB

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Neston / Cheshire
  • Posts: 992
    • 2.5 V6 CDX Manual (MFL)
    • View Profile
Re: heater vent dial illumination ? build gone or is it just me ?
« Reply #4 on: 19 December 2013, 23:53:08 »

Cheers.   :y

Probably do passenger one too, as I bet as soon as I do the blown ones the working passenger one will blow  ::)

Logged

05omegav6

  • Guest
Re: heater vent dial illumination ? build gone or is it just me ?
« Reply #5 on: 20 December 2013, 00:00:12 »

Passenger one as easy as drivers side :y

Might as well do the one for the rear vents whilst you're on a roll ::)
Logged
Pages: [1]   Go Up
 

Page created in 0.012 seconds with 17 queries.