Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1] 2 3  All   Go Down

Author Topic: Multiram valve number 2...(behind the coilpack)  (Read 6097 times)

0 Members and 2 Guests are viewing this topic.

calibrated

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Croatia
  • Posts: 61
    • Opel Calibra
    • View Profile
Multiram valve number 2...(behind the coilpack)
« on: 13 January 2016, 21:21:12 »
What is natural position of multiram valve after 4000 rpm? Should it remain in position for example when engine is off or should it operate in direction of coilpack? (opening or closing inlet)
Logged

zirk

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Epping Forest
  • Posts: 11444
  • 3.2 Manual Special Saloon ReMapped and LPG'd and
    • 3.2 Manual Special Estate
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #1 on: 13 January 2016, 21:55:23 »
Open, there both open at full revs (shortest velocity).

Edit, both open at more than 4100.
Logged

calibrated

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Croatia
  • Posts: 61
    • Opel Calibra
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #2 on: 14 January 2016, 02:03:32 »
Thank you
Logged

polilara

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Finland
  • Posts: 1102
    • 2.6 Y26SE Elegance 2001
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #3 on: 14 January 2016, 05:44:10 »
Logged

terry paget

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Midsomer Norton Somerset
  • Posts: 4633
    • 3 Astras 2 Vectra
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #4 on: 14 January 2016, 08:15:26 »
But note that valve 2 (in the plenum) must be open at idle on early engines with idle control valves on 2,4,6 side, but should close between idle and 3400rpm to give more torque. I have known them stuck open, so engine ran, with poor low rev torque.
Logged

Kevin Wood

  • Global Moderator
  • *****
  • Offline Offline
  • Gender: Male
  • Alton, Hampshire
  • Posts: 36434
    • Jaguar XE 25t, Westfield
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #5 on: 14 January 2016, 10:07:13 »
Yep, I think it's open on all cars at idle to balance the airflow across the banks. It closes once the engine is under load, and opens again at 4100 RPM.
Logged
Tech2 services currently available. See TheBoy's price list: http://theboy.omegaowners.com/

Webby the Bear

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northampton
  • Posts: 12729
    • 2000 (W Reg.) 2.5 V6 CD
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #6 on: 20 January 2016, 18:33:35 »
Not wishing to bump but...

I wanted to double check these were working prior to me doing my proper 0-60 test  :D I can't get either of them to move  :o though the car doesn't seem down on power particularly.

So. just so I've got this right...... whilst looking at the rear multiram (plenum) it should move when throttle on...... then at 4100k rpm the front one in the trumpets should move. correct?

if so am I right that it has to be stuck open/closed valves? as I believe any electrical issue will put the EML on (something I found when I forgot to plug it in  ::))
Logged
RIP Paul Lovejoy

Webby the Bear

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northampton
  • Posts: 12729
    • 2000 (W Reg.) 2.5 V6 CD
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #7 on: 20 January 2016, 19:30:29 »
ps, just to add I do have hissing when vac lines pulled from vac tanks...so I knowthey are good :)
Logged
RIP Paul Lovejoy

Webby the Bear

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northampton
  • Posts: 12729
    • 2000 (W Reg.) 2.5 V6 CD
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #8 on: 23 January 2016, 19:48:19 »
Anyone?

Just to add I got the front one to move. But the rear plenum one is definitely not moving.

I have a spare plenum. Is it worth swapping the valve. Or maybe sticking the spare plenum on. I don't believe it can be electrical as it would throw a code. Any advice welcome.

Ps got the front one to move. Previously I must not have revved it hard enough
Logged
RIP Paul Lovejoy

05omegav6

  • Guest
Re: Multiram valve number 2...(behind the coilpack)
« Reply #9 on: 23 January 2016, 19:52:10 »
Quote from: Webby the Bear on 23 January 2016, 19:48:19
Anyone?

Just to add I got the front one to move. But the rear plenum one is definitely not moving.

I have a spare plenum. Is it worth swapping the valve. Or maybe sticking the spare plenum on. I don't believe it can be electrical as it would throw a code. Any advice welcome.

Ps got the front one to move. Previously I must not have revved it hard enough
Swapping the plenums is as quick and easy as swapping the solenoid and valve :y
Logged

Webby the Bear

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northampton
  • Posts: 12729
    • 2000 (W Reg.) 2.5 V6 CD
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #10 on: 23 January 2016, 19:57:03 »
Quote from: Harris K Telemacher on 23 January 2016, 19:52:10
Quote from: Webby the Bear on 23 January 2016, 19:48:19
Anyone?

Just to add I got the front one to move. But the rear plenum one is definitely not moving.

I have a spare plenum. Is it worth swapping the valve. Or maybe sticking the spare plenum on. I don't believe it can be electrical as it would throw a code. Any advice welcome.

Ps got the front one to move. Previously I must not have revved it hard enough
Swapping the plenums is as quick and easy as swapping the solenoid and valve :y

Cheers mate. Got to take plenum off anyway as I got some breathers to clean too 👍
Logged
RIP Paul Lovejoy

Webby the Bear

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northampton
  • Posts: 12729
    • 2000 (W Reg.) 2.5 V6 CD
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #11 on: 24 January 2016, 14:42:50 »
Is the rear multram from a 3l plenum fittable to the 2.5l plenum? It's the only one I have spare. Gutted as I thought I had the full plenum. Grrr
Logged
RIP Paul Lovejoy

05omegav6

  • Guest
Re: Multiram valve number 2...(behind the coilpack)
« Reply #12 on: 24 January 2016, 14:44:29 »
Quote from: Webby the Bear on 24 January 2016, 14:42:50
Is the rear multram from a 3l plenum fittable to the 2.5l plenum? It's the only one I have spare. Gutted as I thought I had the full plenum. Grrr
All the multiram items are the same :y
Logged

Webby the Bear

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northampton
  • Posts: 12729
    • 2000 (W Reg.) 2.5 V6 CD
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #13 on: 24 January 2016, 17:00:46 »
Quote from: Harris K Telemacher on 24 January 2016, 14:44:29
Quote from: Webby the Bear on 24 January 2016, 14:42:50
Is the rear multram from a 3l plenum fittable to the 2.5l plenum? It's the only one I have spare. Gutted as I thought I had the full plenum. Grrr
All the multiram items are the same :y

Great news. Thanks Taxi  :y

With the car off I moved the plunger and it seems to move with ease. There was a slight air escaping / sucking type noise from the diaphragm looking thing. Possible air leak causing it not to move I wonder  :-\
Logged
RIP Paul Lovejoy

DrAndyB

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Neston / Cheshire
  • Posts: 995
    • 2.5 V6 CDX Manual (MFL)
    • View Profile
Re: Multiram valve number 2...(behind the coilpack)
« Reply #14 on: 25 January 2016, 19:18:37 »
I would be interested to hear if you get to the bottom of your issue, as I am convinced my rear multiram is the same.  Front multiram Definitely moves when blip above 4k rmp but rear not move at all.  Moves freely enough when press plunger and no noticeable air escaping and connector to solenoid is in  :-\

Keep posted of your progress  :y
Logged
Pages: [1] 2 3  All   Go Up
« previous next »
 

Page created in 0.011 seconds with 17 queries.