Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: 1 [2]  All   Go Down

Author Topic: (Rover) Any idea on removing CV joints  (Read 3276 times)

0 Members and 2 Guests are viewing this topic.

henryd

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • west cornwall
  • Posts: 8806
  • VW Touareg R5 tdi Auto
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #15 on: 27 September 2010, 19:24:44 »
Quote
Been a few years since i've done a rover joint but if they are the same as the GM FWD ones, remove the boot, clear out as much grease as possible then have a feel round inside the joint for the circlip.

Use a good set of external circlip pliers in one hand, copper or soft face hammer in the other hand and pull the joint with other hand.....

Did i memtion you need three hands ;D

Andy

not the same as vauxhall,circlip is hidden,knock off with a hammer :y
Logged
other rides 
  mk3 Volvo v70 2.0 Diesel ,Citroen C2, Pug 306 cabriolet
  Sterling elite trekker pikey wagon

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 107163
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #16 on: 27 September 2010, 20:19:06 »
Cheers guys :y

One side done, darkness, rain and extreme hunger prevented other side being done tonight.

I'm not allowed tea until I'm bathed :(. Hence laying in the bath, on OOF :P
Logged
Grumpy old man

aaronjb

  • Guest
Re: (Rover) Any idea on removing CV joints
« Reply #17 on: 27 September 2010, 20:40:11 »
Don't drop the laptop, that could have a shocking outcome!  ;D
Logged

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 107163
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #18 on: 27 September 2010, 20:49:53 »
Quote
Don't drop the laptop, that could have a shocking outcome!  ;D
The old one went in a few times ;D.  It lasted remarkably well, but I think the water eventually killed it  :'(

This HP one has yet to fall in the bath, but has been left out in the rain more than once (last time being Newent ;D)
Logged
Grumpy old man

aaronjb

  • Guest
Re: (Rover) Any idea on removing CV joints
« Reply #19 on: 27 September 2010, 21:08:27 »
 ;D ;D I've known people drop phones in baths..

I've even known a guy who took his Blackberry in the shower..

But I hadn't known anyone who'd dropped a laptop in the bath until now  ;D
Logged

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #20 on: 27 September 2010, 22:24:10 »
IIRC the outer CV joint came off the drive shafts quite easy with a bit of a tap and I don't remember the driveshaft being held in the gearbox either but it was a couple of years since I have done the CV joints on mine and my daughters 25s ::)
Logged
Retired

CaptainZok

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Bolton
  • Posts: 8093
  • Victim of Cyberbullying.
    • 3.2 MV6 Estate
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #21 on: 28 September 2010, 03:01:00 »
The Gnome swears by his favourite tool the FBH ( Slapon of course). ;D
Logged
PM me for code reading/clearing
TuBy's new whipping boy.

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #22 on: 28 September 2010, 09:15:46 »
Quote
The Gnome swears by his favourite tool the FBH ( Slapon of course). ;D
Ah yes the FBH also know as the Negotiator, idiotometer ect ;D
Logged
Retired

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 107163
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #23 on: 28 September 2010, 19:42:15 »
Other side done tonight :)

Had trouble getting the boot clips tight - driveshaft end I used a cable tie, but the large one, had to use clip. Not convinced its tight enough  :-/
Logged
Grumpy old man

Lazydocker

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Woodbridge, Suffolk
  • Posts: 18848
  • Constantly Bullied by a certain Admin
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #24 on: 29 September 2010, 20:49:52 »
Quote
Other side done tonight :)

Had trouble getting the boot clips tight - driveshaft end I used a cable tie, but the large one, had to use clip. Not convinced its tight enough  :-/

They're a right PITA ::) ::)

Hope you made sure there was no grease on the mating faces of the boot and the joint ;) ;) :y
Logged
Whatever it is... I didn't do it

Brikhead

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • West-Mids.
  • Posts: 1540
  • Sleeping. Do not disturb.
    • 2003 chitroen Saxo
    • View Profile
Re: (Rover) Any idea on removing CV joints
« Reply #25 on: 29 September 2010, 21:42:59 »
Quote
Had trouble getting the boot clips tight - driveshaft end I used a cable tie, but the large one, had to use clip. Not convinced its tight enough  :-/

Join two cable ties together if needs be... I try to use the metal clips though, cable tied ones have come loose for me in the past.


Logged
Pages: 1 [2]  All   Go Up
« previous next »
 

Page created in 0.018 seconds with 17 queries.