Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Search the maintenance guides for answers to 99.999% of Omega questions

Pages: [1] 2  All   Go Down

Author Topic: Dead stuck on timing belt!!!!!  (Read 3622 times)

0 Members and 1 Guest are viewing this topic.

megaomega123

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • 0
  • Posts: 915
    • View Profile
Dead stuck on timing belt!!!!!
« on: 04 August 2007, 20:54:11 »
Got the belt on upto the crank turn point. Started to turn crank and it turned but the cams didnt turn. Sounded like the belt was slipping around the crank. Now I can't turn the crank at all  :'( :'(
Logged
ʎɐqǝ uo pɹɐoqʎǝʞ ɐ ʎnq ı ǝɯıʇ ʇsɐן ǝɥʇ sı sıɥʇ.

Andy B

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • Bury Lancs
  • Posts: 39886
    • ML350 TDM SmartRoadster
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #1 on: 04 August 2007, 21:16:46 »
Quote
Got the belt on upto the crank turn point. Started to turn crank and it turned but the cams didnt turn. Sounded like the belt was slipping around the crank. Now I can't turn the crank at all  :'( :'(

If you were turning the crank and the cams were not turning is sounds to me as though you now have pistons hard up to open valves. I hope you haven't tried to force the crank round. You should if you're careful be able to turn the crank back to were you started, and have another attempt at lacing the cam belt up around all the pulleys.
Some pictures might help diagnosis
Logged

JamesV6CDX

  • Omega Queen
  • *****
  • Offline Offline
  • Gloucestershire/Buckinghamshire
  • Posts: 16656
    • Omega 3.2 Retail MV6 LPG
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #2 on: 04 August 2007, 21:17:49 »
We have determined by MSN that the cams and crank are now all over the shop.

Next step, is to carefully get them all back locked into correct positions

Then get the belt re-fitted, keeping crank locked at all times so it can't slip when tensioning etc...

When this is done, Before cranking by hand, just check there is no abnormal slack anywhere on the cambelt..
Logged

Matchless

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Nottingham
  • Posts: 1563
    • A white van
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #3 on: 04 August 2007, 21:22:14 »
bit more detail / more words would help.

Were you turning the crank clockwise?
Did the cams move at all / will the cam-locks go back in?

Post more detail and we will try to help but in the meantime do not turn the crank further, you risk bending valves!!
Logged

Matchless

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Nottingham
  • Posts: 1563
    • A white van
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #4 on: 04 August 2007, 21:25:51 »
Think Im in an NTL time-warp, earlier posts are popping up after more recent ones :-? :-?
Logged

megaomega123

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • 0
  • Posts: 915
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #5 on: 04 August 2007, 21:40:02 »
Well, how pi**ed off am I? I did everything by the book, checked and checked again. I didn't force the crank, it just reached a point and wouldn't turn, that's when I shouted help to James.

Now have the belt off again and have had to leave it for the night. I think I'll have to get someone to take it from here as this has knocked my confidence big time.

Anyway keep you posted thanks.
Big thanks to James  :y
Logged
ʎɐqǝ uo pɹɐoqʎǝʞ ɐ ʎnq ı ǝɯıʇ ʇsɐן ǝɥʇ sı sıɥʇ.

Pete Elite

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Uxbridge, Middlesex
  • Posts: 1749
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #6 on: 04 August 2007, 23:19:13 »
  Hi,
     I've just done my Cambelt, not without problems i might add but with Marks help managed to sort it out and get it done.

 Having done it, although not making me an expert does give you the benefit of the experience and not to trying to sound critical, did you remove the Cam locking tools before you tried to turn the crank!

 Sounds daft i know but it's the simply things you think of least :-?.

     Sorry if this not the cause and no offence meant :y.
Logged

JamesV6CDX

  • Omega Queen
  • *****
  • Offline Offline
  • Gloucestershire/Buckinghamshire
  • Posts: 16656
    • Omega 3.2 Retail MV6 LPG
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #7 on: 04 August 2007, 23:35:31 »
Removing the camlocks before turning was the first thing I asked ;)

As said, I'm likely to be in your area of Sunny Scooootlnd on Monday, so we'll chat further...

Just don't force anything in the meantime :y
Logged

megaomega123

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • 0
  • Posts: 915
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #8 on: 05 August 2007, 13:05:19 »
If I manually move the cams with the tx50, how much resistance should there be? I don't want to force anything. Bearing in mind that the crank is no longer at TDC.
Logged
ʎɐqǝ uo pɹɐoqʎǝʞ ɐ ʎnq ı ǝɯıʇ ʇsɐן ǝɥʇ sı sıɥʇ.

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 107521
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #9 on: 05 August 2007, 13:33:50 »
Quote
If I manually move the cams with the tx50, how much resistance should there be? I don't want to force anything. Bearing in mind that the crank is no longer at TDC.
how far off tdc is it?

I'm thinking cams need to go half this distance, then slap a belt on to get it all safely back to tdc, and redo.  Before attempting, get this confirmed by one of the experts here first...
Logged
Grumpy old man

megaomega123

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • 0
  • Posts: 915
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #10 on: 05 August 2007, 13:56:56 »
Quote
Quote
If I manually move the cams with the tx50, how much resistance should there be? I don't want to force anything. Bearing in mind that the crank is no longer at TDC.
how far off tdc is it?

I'm thinking cams need to go half this distance, then slap a belt on to get it all safely back to tdc, and redo.  Before attempting, get this confirmed by one of the experts here first...

Crank was TDC when I started to turn. I would say that it turned 45 deg without the cams turning, so 45 degs off TDC. I attempted to adjust cam 1 manually, but it kept springing back. Every cam is way off timing marks now and all cams are at different positions  :-/  
Logged
ʎɐqǝ uo pɹɐoqʎǝʞ ɐ ʎnq ı ǝɯıʇ ʇsɐן ǝɥʇ sı sıɥʇ.

JamesV6CDX

  • Omega Queen
  • *****
  • Offline Offline
  • Gloucestershire/Buckinghamshire
  • Posts: 16656
    • Omega 3.2 Retail MV6 LPG
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #11 on: 05 August 2007, 14:00:01 »
Quote
Quote
Quote
If I manually move the cams with the tx50, how much resistance should there be? I don't want to force anything. Bearing in mind that the crank is no longer at TDC.
how far off tdc is it?

I'm thinking cams need to go half this distance, then slap a belt on to get it all safely back to tdc, and redo.  Before attempting, get this confirmed by one of the experts here first...

Crank was TDC when I started to turn. I would say that it turned 45 deg without the cams turning, so 45 degs off TDC. I attempted to adjust cam 1 manually, but it kept springing back. Every cam is way off timing marks now and all cams are at different positions  :-/  

As an aside, when moving cam pulleys, you need to use a little tommy/breaker bar, not a ratchet...
Logged

megaomega123

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • 0
  • Posts: 915
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #12 on: 05 August 2007, 14:02:19 »
Quote
Quote
Quote
Quote
If I manually move the cams with the tx50, how much resistance should there be? I don't want to force anything. Bearing in mind that the crank is no longer at TDC.
how far off tdc is it?

I'm thinking cams need to go half this distance, then slap a belt on to get it all safely back to tdc, and redo.  Before attempting, get this confirmed by one of the experts here first...

Crank was TDC when I started to turn. I would say that it turned 45 deg without the cams turning, so 45 degs off TDC. I attempted to adjust cam 1 manually, but it kept springing back. Every cam is way off timing marks now and all cams are at different positions  :-/  

As an aside, when moving cam pulleys, you need to use a little tommy/breaker bar, not a ratchet...
Does that signify that they are hard to move and need a bit of force?
Logged
ʎɐqǝ uo pɹɐoqʎǝʞ ɐ ʎnq ı ǝɯıʇ ʇsɐן ǝɥʇ sı sıɥʇ.

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #13 on: 05 August 2007, 15:12:52 »
No it just means the cams when past a certain point will spin and a ratchet wont stop them where as a T bar will :y
Logged
Retired

Elite Pete

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Chester
  • Posts: 19580
  • My spider senses are tingling
    • Audi SQ5 GSX1400
    • View Profile
Re: Dead stuck on timing belt!!!!!
« Reply #14 on: 05 August 2007, 15:16:28 »
Quote
Quote
If I manually move the cams with the tx50, how much resistance should there be? I don't want to force anything. Bearing in mind that the crank is no longer at TDC.
how far off tdc is it?

I'm thinking cams need to go half this distance, then slap a belt on to get it all safely back to tdc, and redo.  Before attempting, get this confirmed by one of the experts here first...
IIRC the crankshaft needs to be at 4oclock before the cams can realigned safely but again I would wait for the experts just to make sure :y
Logged
Retired
Pages: [1] 2  All   Go Up
« previous next »
 

Page created in 0.038 seconds with 17 queries.