Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1]   Go Down

Author Topic: Positioning rear axle stands  (Read 1527 times)

0 Members and 1 Guest are viewing this topic.

ians

  • Omega Baron
  • *****
  • Offline Offline
  • Reading
  • Posts: 3394
    • View Profile
Positioning rear axle stands
« on: 08 December 2007, 10:24:02 »
Can someone please confirm it is acceptable to position axle stands under the box section of the rear subframe as I believe Mark has done in the photos in the this guide? http://www.omegaowners.com/forum/YaBB.pl?num=1152564750  

Or is the trailing arm a better bet?   This is for my handbrake work so no suspension access issues.

Cheers

Ian
Logged

Andy B

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • Bury Lancs
  • Posts: 39876
    • ML350 TDM SmartRoadster
    • View Profile
Re: Positioning rear axle stands
« Reply #1 on: 08 December 2007, 10:28:30 »
Quote
......Or is the trailing arm a better bet?    ....
Ian

You'll bend things if you support your car on the trailing arms. Chassis box section or the axle half shafts are a better bet.
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 34095
  • Git!
    • View Profile
Re: Positioning rear axle stands
« Reply #2 on: 08 December 2007, 10:34:29 »
As per the picture....on the sections shown......VERY strong.

You do have to make sure the cup of the jack is on the front edge of the mounting point so the stands will fit.
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 34095
  • Git!
    • View Profile
Re: Positioning rear axle stands
« Reply #3 on: 08 December 2007, 10:35:18 »
Quote
axle half shafts are a better bet.

Thats not a good idea.....do you REALY mean the half shafts!
Logged

ians

  • Omega Baron
  • *****
  • Offline Offline
  • Reading
  • Posts: 3394
    • View Profile
Re: Positioning rear axle stands
« Reply #4 on: 08 December 2007, 10:39:27 »
Mark - have you put them on the subframe section between the mounting plate and the centre of the car, or actually on the mounting plate itself (bit difficult to see exactly on the pics)?   I can understand its difficult to jack on the mounting plate and position an axle stand there at the same time..
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 34095
  • Git!
    • View Profile
Re: Positioning rear axle stands
« Reply #5 on: 08 December 2007, 10:40:52 »
I have jacked on the mounting plate (front edge)........and then placed the stand under the large section of sub frame which heads towards the diff....
Logged

ians

  • Omega Baron
  • *****
  • Offline Offline
  • Reading
  • Posts: 3394
    • View Profile
Re: Positioning rear axle stands
« Reply #6 on: 08 December 2007, 10:43:06 »
Brilliant - thanks Mark.  Now time to get cold and wet :(
Logged

Andy B

  • Get A Life!!
  • *****
  • Online Online
  • Gender: Male
  • Bury Lancs
  • Posts: 39876
    • ML350 TDM SmartRoadster
    • View Profile
Re: Positioning rear axle stands
« Reply #7 on: 08 December 2007, 10:45:00 »
Quote
Quote
axle half shafts are a better bet.

Thats not a good idea.....do you REALY mean the half shafts!

maybe not then.  :-[
Logged

Dave-C

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Staffordshire
  • Posts: 1915
  • The Old Girl
    • View Profile
Re: Positioning rear axle stands
« Reply #8 on: 08 December 2007, 11:27:45 »
Quote
Quote
......Or is the trailing arm a better bet?    ....
Ian

You'll bend things if you support your car on the trailing arms. Chassis box section or the axle half shafts are a better bet.

Please NO!
Logged
Do it right, do it once................
Pages: [1]   Go Up
« previous next »
 

Page created in 0.011 seconds with 16 queries.