Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[fos605]

Gettimg a rattle noise from around drivers side front wheel.  The only thing I can find loose at all is the front disc pad. There was nothing to stop it moving around and the noise did seem appropriate, however  
I have v6 2.5 and am told there is no "antirattle spring" .

Has anyone had any similar experience and could suggest ideas to cure it.

Really noticable when travelling over rough roads.

[Richard A]

Can be the disc metal back plate, if it gets bent it can make contact with the rotating disc, makes a lot noise over broken surfaces, bend it out of the way, also check drop links.
regards
richard a

[fos605]

Thanks Richard,  but it doesnt seem like the back plate,  excuse my ignorance but what are drop links?

[Darth Loo-knee]

This is a droplink mate

[fos605]

Thanks for the photo.

I now its hard to describe noises, but I would have thought if the drop link was worn then it would have made a knoking noise, not the rattle type of noise I am getting.

I am almost sure it is the front pad loose,  As I said I was expecting a spring clip type of thing, I think they are called antirattle spring, but am told on this model they are not, so what is there to stop them from rattling?

[Darth Loo-knee]

Your welcome for the picture
If the droplink is knackered it does make a clonking noise when you go over bumps mate

As for your rattling you think its your pad you say? when you fitted them did you put copper grease on the rear of it? i think this is supposed to stop rattling.
If I remember rightly there are two dowels that go through the holes on the pads and there is a spring that holds the pad in place... it is a while since doing mne so i could be wrong!!

[fos605]

I havent changed the pads recently.  but will try the copper grease this weekend.  Many thanks for you suggestions.

[Darth Loo-knee]

Are they worn then and perhaps moving more than usual?

[FRE07962128]

Can be the disc metal back plate, if it gets bent it can make contact with the rotating disc, makes a lot noise over broken surfaces, bend it out of the way, also check drop links.
regards
richard a

I had the same thing on my old Toyota, which a garage claimed was a wheel bearing going!  Flaming muppets!  It took me 3 minutes to find this out and two minutes to adjust this plate to stop it rubbing on the back of the disc.

[fos605]

No I dont think they are worn too much.

Will have a good look over the weekend (again)
I did find one of the caliper guides seized but managed to free that OK, which at the time I thought I had found the fault, but still the rattle!!

[FRE07962128]

Gettimg a rattle noise from around drivers side front wheel.  The only thing I can find loose at all is the front disc pad. There was nothing to stop it moving around and the noise did seem appropriate, however  
I have v6 2.5 and am told there is no "antirattle spring" .

Has anyone had any similar experience and could suggest ideas to cure it.

Really noticable when travelling over rough roads.

How much play is there?  Is the piston hard against the brake pad back plate?
 :-?

[FRE07962128]

No I dont think they are worn too much.

Will have a good look over the weekend (again)
I did find one of the caliper guides seized but managed to free that OK, which at the time I thought I had found the fault, but still the rattle!!

Are any warning brake lights showing on the dash?

[fos605]

Hi Lizzie ,

The pad I think that is causing the rattle is the one on its own nearer the wheel, not the one in contact with the piston.

[FRE07962128]

Right, thanks.  I will think on for you....but how about that back plate? :-?

[FRE07962128]

How much play is there?  Are the holding pins worn / loose?