Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1]   Go Down

Author Topic: geometry where and how ??  (Read 794 times)

0 Members and 1 Guest are viewing this topic.

mick-1975

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • nottingham
  • Posts: 679
    • View Profile
geometry where and how ??
« on: 13 October 2008, 13:51:42 »
 hi everyone just had to put 4 new tyres on my car and had it tracked , would u recommend gettin it cambered aswell ??
  
  if so can anyone reccommend a good place or one of u good guys could do it for us ??????? :y

 thanks to u all in advance mick  :y
« Last Edit: 13 October 2008, 17:02:25 by mick-1975 »
Logged

feeutfo

  • Guest
Re: geometry where and how ??
« Reply #1 on: 13 October 2008, 18:50:12 »
have a search Mick, this has been done to death on here. Depends what problems your having, if you have uneven or excessive tire wear, tram lining or pulling, drifting off to the left or stearing wheel out of line then yes, all roads lead to wheels in motion in Chesham, a bit of a drive for you, for a full geometry set up! Dont even bother with tracking. Complete waste of time as its only a fraction of the problem.
Logged

mick-1975

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • nottingham
  • Posts: 679
    • View Profile
Re: geometry where and how ??
« Reply #2 on: 13 October 2008, 18:58:42 »
thks will do , car pulls to left and inside rim on both sides wear down , i shall have a look , would main dealer do it ? :y
Logged

feeutfo

  • Guest
Re: geometry where and how ??
« Reply #3 on: 13 October 2008, 19:02:11 »
Quote
thks will do , car pulls to left and inside rim on both sides wear down , i shall have a look , would main dealer do it ? :y
NO! Dont even think about it... Somebody tell him!
Logged

Bandit127

  • Guest
Re: geometry where and how ??
« Reply #4 on: 13 October 2008, 19:04:19 »
Quote
Complete waste of time as its only a fraction of the problem.

But when you have 11.5 mm of toe out, quite a large fraction!

Have a search on the forum Mick. And check out Wheels In Motion's website here:
Clicky

FYI, Wheels In Motion are usually referred to as WIM on here...  


« Last Edit: 13 October 2008, 19:04:48 by Bandit127 »
Logged

mick-1975

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • nottingham
  • Posts: 679
    • View Profile
Re: geometry where and how ??
« Reply #5 on: 13 October 2008, 19:05:16 »
ok i guess thats a no then goin to main dealer , !!

  i shall avoid that place like the plague then  ;D ;D
   thks for the post  :y
Logged

feeutfo

  • Guest
Re: geometry where and how ??
« Reply #6 on: 13 October 2008, 20:22:12 »
Quote
ok i guess thats a no then goin to main dealer , !!

  i shall avoid that place like the plague then  ;D ;D
   thks for the post  :y

Only door to go through at vx is the parts door. Dont let them actually touch your car. As you live in nottingham any work should be done by Mark dtm where ever possible. Shame not to use him if you live so close, have a search, its a bit fussy but should bring up something... :-)
Logged

Marks DTM Calib

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • West Bridgford
  • Posts: 34016
  • Git!
    • View Profile
Re: geometry where and how ??
« Reply #7 on: 13 October 2008, 20:38:50 »
I can set the camber.....but then pop down to Loughborough to Fleet Fit Tyres to get the rest set.
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.012 seconds with 16 queries.