Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1] 2  All   Go Down

Author Topic: Help! Removing idler arm.  (Read 2030 times)

0 Members and 1 Guest are viewing this topic.

manny

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • bromorough.Wirral.
  • Posts: 238
    • View Profile
Help! Removing idler arm.
« on: 01 November 2008, 13:03:13 »
Tring to fit new idler arm.Got it all apart but cannot get the bloody ball joint to come off idler arm.Ive got a ball joint seperator but it wont go on.Any idears?
Logged
2001 OMEGA MV6

chrismec

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • Poole Dorset
  • Posts: 20
    • View Profile
Re: Help! Removing idler arm.
« Reply #1 on: 01 November 2008, 13:06:21 »
Umm bigger hammer  :D
Logged
If it ain't broke don't fix it

manny

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • bromorough.Wirral.
  • Posts: 238
    • View Profile
Re: Help! Removing idler arm.
« Reply #2 on: 01 November 2008, 13:10:35 »
Quote
Umm bigger hammer  :D
Got one.
Logged
2001 OMEGA MV6

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39778
    • ML350 TDM SmartRoadster
    • View Profile
Re: Help! Removing idler arm.
« Reply #3 on: 01 November 2008, 13:11:05 »
What Chrismec meant was ..... TWO bigger hammers! ::) ;D ;D ;D
Try to hit either side of the ball joint at the same time, it'll let go eventually.  ;)
Logged

manny

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • bromorough.Wirral.
  • Posts: 238
    • View Profile
Re: Help! Removing idler arm.
« Reply #4 on: 01 November 2008, 13:12:28 »
Quote
What Chrismec meant was ..... TWO bigger hammers! ::) ;D ;D ;D
Try to hit either side of the ball joint at the same time, it'll let go eventually.  ;)
Ill give it a try.
Logged
2001 OMEGA MV6

chrismec

  • Newbie
  • *
  • Offline Offline
  • Gender: Male
  • Poole Dorset
  • Posts: 20
    • View Profile
Re: Help! Removing idler arm.
« Reply #5 on: 01 November 2008, 13:26:39 »
Quote
What Chrismec meant was ..... TWO bigger hammers! ::) ;D ;D ;D
Try to hit either side of the ball joint at the same time, it'll let go eventually.  ;)
yes exactly, but if your using a fork type splitter you may need to hit it a bit harder(they can be a bit childish some times)
Logged
If it ain't broke don't fix it

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39778
    • ML350 TDM SmartRoadster
    • View Profile
Re: Help! Removing idler arm.
« Reply #6 on: 01 November 2008, 13:43:36 »
Quote
......
yes exactly, but if your using a fork type splitter you may need to hit it a bit harder(they can be a bit childish some times)

But they mean you'll need a new ball joint too.
Logged

manny

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • bromorough.Wirral.
  • Posts: 238
    • View Profile
Re: Help! Removing idler arm.
« Reply #7 on: 01 November 2008, 13:54:50 »
Just tried new idler on shaft and its got loads of play????Hole is to big???Non vaux part?????
Logged
2001 OMEGA MV6

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39778
    • ML350 TDM SmartRoadster
    • View Profile
Re: Help! Removing idler arm.
« Reply #8 on: 01 November 2008, 14:07:22 »
Quote
Just tried new idler on shaft and its got loads of play????Hole is to big???Non vaux part?????

That's right, I did the same thing. I'd expected a nice slide on fit, but when you tighten it up it'll be OK. :y :y :y
Logged

manny

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • bromorough.Wirral.
  • Posts: 238
    • View Profile
Re: Help! Removing idler arm.
« Reply #9 on: 01 November 2008, 14:32:16 »
Quote
Quote
Just tried new idler on shaft and its got loads of play????Hole is to big???Non vaux part?????

That's right, I did the same thing. I'd expected a nice slide on fit, but when you tighten it up it'll be OK. :y :y :y
No ive measured it with a vernier?? gauge and its half a mill bigger???
Logged
2001 OMEGA MV6

manny

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • bromorough.Wirral.
  • Posts: 238
    • View Profile
Re: Help! Removing idler arm.
« Reply #10 on: 01 November 2008, 15:33:04 »
Quote
Quote
Quote
Just tried new idler on shaft and its got loads of play????Hole is to big???Non vaux part?????

That's right, I did the same thing. I'd expected a nice slide on fit, but when you tighten it up it'll be OK. :y :y :y
No ive measured it with a vernier?? gauge and its half a mill bigger???
Does the play on the internal diamitter close up when its tightened or is it a duff one????
Logged
2001 OMEGA MV6

razzo

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Crapital
  • Posts: 1206
    • 97 3.0 Elite
    • View Profile
Re: Help! Removing idler arm.
« Reply #11 on: 01 November 2008, 15:47:05 »
the play should go as you tighten the nut iirc its a taper fit
Logged

Seth

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • South Wales Valleys
  • Posts: 6646
  • If there's a 'system' - play it ... !
    • '99 2.5TD GLS Estate
    • View Profile
Re: Help! Removing idler arm.
« Reply #12 on: 01 November 2008, 15:55:12 »
Use two lump hammers, and simultaneously clout either side of the eye of the idler arm.
A couple of good resounding blows should see the joint separate from the tie-rod. I've not failed yet using this method ... !
Logged
Gettin' seriously hacked-off by those who ignore the wisdom of proven experience ... and Forum guidelines.

manny

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • bromorough.Wirral.
  • Posts: 238
    • View Profile
Re: Help! Removing idler arm.
« Reply #13 on: 01 November 2008, 16:26:11 »
Quote
the play should go as you tighten the nut iirc its a taper fit
I hear see what your saying but when i put it on and tightened it up you could feel play in it.Just by putting my finger in it you can feel the hole is bigger on the new one?
Logged
2001 OMEGA MV6

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39778
    • ML350 TDM SmartRoadster
    • View Profile
Re: Help! Removing idler arm.
« Reply #14 on: 01 November 2008, 16:57:13 »
Quote
the play should go as you tighten the nut iirc its a taper fit
We're at the larger end of the steering arm, you're talking about the small ball joint end. ;)  :y
Logged
Pages: [1] 2  All   Go Up
« previous next »
 

Page created in 0.01 seconds with 17 queries.