Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: [1]   Go Down

Author Topic: Creamy coolant problem  (Read 1415 times)

0 Members and 1 Guest are viewing this topic.

RobseyMV6

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • west sussex
  • Posts: 743
    • View Profile
Creamy coolant problem
« on: 16 December 2008, 19:03:35 »
I have a 3.2 omega with a problem.... coolant bottle blow with the result of hole system full with cream, i did a cly test and number 6 cly only gave 40psi? others 160>180 so removed head and had skimed then tested cly 6 again once replaced result was 150psi but it still has the problem with cream in coolant? as the fan didn't cut in at weekend when i run the car up, the top hose blow off... now could this be a oil cooler problem or a damaged cly head? Any advice would be great  :y
Logged

hotel21

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • The Kingdom of Fife
  • Posts: 13021
    • View Profile
Re: Creamy coolant problem
« Reply #1 on: 16 December 2008, 19:15:44 »
Ensure all the mayo crud has been flushed from the engine and once done, refill with correct mix of antifreeze solution.

Short journeys also give mayo buildup in the filler neck as its open to additional colling air within the engine bay.

If the dipstick is got good clean oil, fair chance you have fixed the problem.

Also, check the maintenance section.  Theres a flow chart there to let you suss whether the gasket is still fubar or the oil cooler is now duff...
« Last Edit: 16 December 2008, 19:18:54 by hotel21 »
Logged

hotel21

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • The Kingdom of Fife
  • Posts: 13021
    • View Profile
Re: Creamy coolant problem
« Reply #2 on: 16 December 2008, 19:16:41 »
... and please rsize your avatar.  Its humungeous!
Logged

Lizzie_Zoom

  • Guest
Re: Creamy coolant problem
« Reply #3 on: 16 December 2008, 19:26:54 »
Quote
... and please rsize your avatar.  Its humungeous!


Yes it has taken over virtually the whole text area so all I can read is the first sentence.  :o :o :o
Logged

Entwood

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • North Wiltshire
  • Posts: 19566
  • My Old 3.2 V6 Elite (LPG)
    • Audi A6 Allroad 3.0 DTI
    • View Profile
Re: Creamy coolant problem
« Reply #4 on: 16 December 2008, 19:35:44 »
Quote
... and please rsize your avatar.  Its humungeous!


1024 x 738 !!!!!!!!!!  site limit 110 x 110  !!!   :)
Logged

hotel21

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • The Kingdom of Fife
  • Posts: 13021
    • View Profile
Re: Creamy coolant problem
« Reply #5 on: 16 December 2008, 19:36:50 »
Quote
Quote
... and please rsize your avatar.  Its humungeous!


Yes it has taken over virtually the whole text area so all I can read is the first sentence.  :o :o :o

Avatar link disabled in user profile meantime so that others can actually read the text and offer a reply.

OP - please resize the avatar before re-enabling....
thanks :y
Logged

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 107031
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: Creamy coolant problem
« Reply #6 on: 16 December 2008, 19:54:35 »
Back on topic, sounds like a oil cooler issue if oil in coolant.  The failed HG is likely due to overheating due to poor coolant circ due to being sludge.
Logged
Grumpy old man

RobseyMV6

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • west sussex
  • Posts: 743
    • View Profile
Re: Creamy coolant problem
« Reply #7 on: 17 December 2008, 19:05:40 »
Thanks for all advice, will change oil cooler this weekend and give engine a good flush  :y

Logged

m1ct

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Female
  • Surrey
  • Posts: 342
    • View Profile
Re: Creamy coolant problem
« Reply #8 on: 21 December 2008, 19:36:18 »
Quote
Back on topic, sounds like a oil cooler issue if oil in coolant.  The failed HG is likely due to overheating due to poor coolant circ due to being sludge.
Well, new oil cooler is in place now. Also flushed cooling system twice and saw improvement at last! but fan didn`t cut in when it should! Switched the mig off before it cooked but built up pressure blew the hose off  [smiley=undecided.gif]
Could this be one of radiator heat sensors? (either wm or xa, or both?)
Any advice much appreciated
Marti
Logged

Kevin Wood

  • Global Moderator
  • *****
  • Offline Offline
  • Gender: Male
  • Alton, Hampshire
  • Posts: 36417
    • Jaguar XE 25t, Westfield
    • View Profile
Re: Creamy coolant problem
« Reply #9 on: 21 December 2008, 22:02:41 »
I have seen radiator switches build up a film of crud on them which insulates them, causing an overheat, so try taking out the radiator fan switch and clean the face, and perhaps another coolant flush for good measure.

While the switch is out, try bridging the contacts and make sure the fans are functioning.

Kevin
Logged
Tech2 services currently available. See TheBoy's price list: http://theboy.omegaowners.com/

Pete Elite

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Uxbridge, Middlesex
  • Posts: 1749
    • View Profile
Re: Creamy coolant problem
« Reply #10 on: 21 December 2008, 22:16:30 »
   Hi Kevin,
               I fitted a new fan switch to my Brother's Renault Laguna the other day after finding power was going to switch and connecting fans directly to the battery and finding that they work ok, but the fans still won't operate on there own when engine gets hot!

   Any ideas :question.

          Cheers,
                    Pete :)
Logged

RobseyMV6

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • west sussex
  • Posts: 743
    • View Profile
Re: Creamy coolant problem
« Reply #11 on: 25 December 2008, 11:23:33 »
Quote
Quote
Back on topic, sounds like a oil cooler issue if oil in coolant.  The failed HG is likely due to overheating due to poor coolant circ due to being sludge.
Well, new oil cooler is in place now. Also flushed cooling system twice and saw improvement at last! but fan didn`t cut in when it should! Switched the mig off before it cooked but built up pressure blew the hose off  [smiley=undecided.gif]
Could this be one of radiator heat sensors? (either wm or xa, or both?)
Any advice much appreciated
Marti
Right all sorted at last and can now rest over xmas :) after flushing system 6 times the slugde is cleared and fans now working thanks to advice from Kevin Wood, also great advice from all other omega owners! Hope you all have a smashing xmas :)
Robsey/M1ct
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.011 seconds with 17 queries.