Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1] 2  All   Go Down

Author Topic: Bonnet release catch doesn't release!!  (Read 3208 times)

0 Members and 1 Guest are viewing this topic.

Arrolman

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Renfrew,Scotland
  • Posts: 391
    • View Profile
Bonnet release catch doesn't release!!
« on: 21 April 2007, 19:35:26 »
Hi,

As above, just moves about freely, how d oI get bonnet open now :-?
Logged
Looking to win the lottery..........

Danny

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Wigan, Greater Manchester
  • Posts: 6483
  • BLACK 1.6 BORA SHAPED JETTA!!
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #1 on: 21 April 2007, 19:42:04 »
how long you had the car?

was it working when you got it?

was it accident damaged?

it could have unclipped somewhere inside, but with my limited knowledge of omegas, my own being the only one anyone's actually let me touch, i wouldnt know just how much you might be able to see from underneath the car
Logged

tunnie

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Surrey
  • Posts: 37547
    • Zafira Tourer & BMW 435i
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #2 on: 21 April 2007, 19:48:31 »
how lose does it feel, does it feel slightly stiff?

Get a freind to lean on the bonnet front, then try pulling the release....
Logged

Danny

  • Omega Lord
  • *****
  • Offline Offline
  • Gender: Male
  • Wigan, Greater Manchester
  • Posts: 6483
  • BLACK 1.6 BORA SHAPED JETTA!!
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #3 on: 21 April 2007, 19:54:40 »
thats what i had to do when i bounced my corsa off a 307 estate :D
Logged

Arrolman

  • Intermediate Member
  • ***
  • Offline Offline
  • Gender: Male
  • Renfrew,Scotland
  • Posts: 391
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #4 on: 21 April 2007, 19:55:01 »
Hi,

Got it open after pulling the wire with pliers, works ok when bonnets open but when closed it goes funny, guessing its the bonnet catch itself, clean and grease tomorrow methinks ::)

Cheers,
Iain
Logged
Looking to win the lottery..........

Dean

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Weston Super Mare - UK
  • Posts: 153
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #5 on: 21 April 2007, 19:56:36 »
I had the same problem, Doing what Tunnie says worked for me..it takes two!

When you have opened it you need to adjust the cable on the right hand side of the front panel...its a matter of undoing the screw, pulling the cable and refastening..

Mine now works spot on!

good luck
Logged
Free Traffic law advice  - Just PM or see the sticky thread in General Chat ! http://www.omegaowners.com/forum/YaBB.pl?num=1177278724 - no liability accepted

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39731
    • ML350 TDM SmartRoadster
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #6 on: 21 April 2007, 20:08:34 »
Quote
I had the same problem, Doing what Tunnie says worked for me..it takes two!

When you have opened it you need to adjust the cable on the right hand side of the front panel...its a matter of undoing the screw, pulling the cable and refastening..

Mine now works spot on!

good luck

Agreed ... but it shouldn't be that tight opening the bonnet in the first place. Either the rubber bonnet stops on either side of the car have been wound up so that they are holding the bonnet high at the sides when it's closed or the bonnet catch itself needs backing off a little so that the bonnet doesn't need to go down quitre as far before it latches.
Logged

TheBoy

  • Administrator
  • *****
  • Offline Offline
  • Gender: Male
  • Brackley, Northants
  • Posts: 106849
  • I Like Lockdown
    • Whatever Starts
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #7 on: 21 April 2007, 20:11:06 »
Adjust the cable properly, and also make sure bonnet stops are correctly set...
Logged
Grumpy old man

stevebubs

  • Junior Member
  • **
  • Offline Offline
  • Reading
  • Posts: 86
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #8 on: 15 March 2009, 20:38:06 »
Think I'm being blind, but I can't see how to adjust....any pics / diagrams?
« Last Edit: 15 March 2009, 20:38:36 by stevebubs »
Logged

kjf7

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • lincolnshire
  • Posts: 236
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #9 on: 15 March 2009, 20:44:10 »
had the same problem with mine pull lever cable goes all slack but pull lever and get a mate to lift bonnet at the same time and no probs then a bit of a clean up and some lube, been fine since :y
Logged

Pete Elite

  • Omega Knight
  • *****
  • Offline Offline
  • Gender: Male
  • Uxbridge, Middlesex
  • Posts: 1749
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #10 on: 15 March 2009, 20:47:12 »
 On the right of the slam panel remove the right hand Rad. cover panel and you'll see the screw holding the cable tight.

  Loosen the screw and take up the slack in the cable a bit at a time until you can open the bonnet ok. :y
Logged

stevebubs

  • Junior Member
  • **
  • Offline Offline
  • Reading
  • Posts: 86
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #11 on: 15 March 2009, 21:54:13 »
Quote
On the right of the slam panel remove the right hand Rad. cover panel and you'll see the screw holding the cable tight.

  Loosen the screw and take up the slack in the cable a bit at a time until you can open the bonnet ok. :y

Spent ages today trying to figure out the adjustment....couldn't see a screw...

Figured out removing the cover panel (2 x screws with 8mm heads) but couldn't see any way of adjusting the cable....
Logged

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39731
    • ML350 TDM SmartRoadster
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #12 on: 15 March 2009, 21:57:27 »
Quote
Quote
On the right of the slam panel remove the right hand Rad. cover panel and you'll see the screw holding the cable tight.

  Loosen the screw and take up the slack in the cable a bit at a time until you can open the bonnet ok. :y

Spent ages today trying to figure out the adjustment....couldn't see a screw...

Figured out removing the cover panel (2 x screws with 8mm heads) but couldn't see any way of adjusting the cable....

Slacken the screw that holds the cable outer sleeve, slide the outer sleeve to the right & re-clamp the outer sleeve.
Logged

stevebubs

  • Junior Member
  • **
  • Offline Offline
  • Reading
  • Posts: 86
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #13 on: 15 March 2009, 22:04:16 »
Quote
Quote
Quote
On the right of the slam panel remove the right hand Rad. cover panel and you'll see the screw holding the cable tight.

  Loosen the screw and take up the slack in the cable a bit at a time until you can open the bonnet ok. :y

Spent ages today trying to figure out the adjustment....couldn't see a screw...

Figured out removing the cover panel (2 x screws with 8mm heads) but couldn't see any way of adjusting the cable....

Slacken the screw that holds the cable outer sleeve, slide the outer sleeve to the right & re-clamp the outer sleeve.

Couldn't find it...will have another look tomorrow....
Logged

Andy B

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Bury Lancs
  • Posts: 39731
    • ML350 TDM SmartRoadster
    • View Profile
Re: Bonnet release catch doesn't release!!
« Reply #14 on: 15 March 2009, 22:11:40 »
Quote
Quote
Quote
Quote
On the right of the slam panel remove the right hand Rad. cover panel and you'll see the screw holding the cable tight.

  Loosen the screw and take up the slack in the cable a bit at a time until you can open the bonnet ok. :y

Spent ages today trying to figure out the adjustment....couldn't see a screw...

Figured out removing the cover panel (2 x screws with 8mm heads) but couldn't see any way of adjusting the cable....

Slacken the screw that holds the cable outer sleeve, slide the outer sleeve to the right & re-clamp the outer sleeve.

Couldn't find it...will have another look tomorrow....

you need to remove the  plastic trim panels over the slam panel, the clamp is towards the right hand side ( as you stand in front of the car)
Logged
Pages: [1] 2  All   Go Up
« previous next »
 

Page created in 0.014 seconds with 17 queries.