Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: [1]   Go Down

Author Topic: Front brake pad orientation  (Read 958 times)

0 Members and 1 Guest are viewing this topic.

amba

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Medway towns
  • Posts: 4827
    • German V6
    • View Profile
Front brake pad orientation
« on: 31 July 2010, 15:00:13 »
Just noticed that new GM pads have 2 different surface for the front pads.
1 side has a rectangle cut out in a piece of glued on fabric....other side is just plain metal with part numbers on.
Question is which side should face the piston ?
Logged

tunnie

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Surrey
  • Posts: 37625
    • Zafira Tourer & BMW 435i
    • View Profile
Re: Front brake pad orientation
« Reply #1 on: 31 July 2010, 15:09:48 »
pad with the rubber on goes on the outside iirc  :y
Logged

amba

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Medway towns
  • Posts: 4827
    • German V6
    • View Profile
Re: Front brake pad orientation
« Reply #2 on: 31 July 2010, 15:11:58 »
That seems to make sense as metal piston is then against metal only .Just wanted to check as didn,t notice that before when changed last time.
Logged

dbug

  • Omega Queen
  • *****
  • Offline Offline
  • Gender: Male
  • Northants
  • Posts: 14279
  • Dont knock Linux!
    • Jaguar XJ 5.0V8 Portfolio
    • View Profile
    • Dbug IT Services
Re: Front brake pad orientation
« Reply #3 on: 31 July 2010, 15:14:26 »
Pad with plain metal backing against caliper piston, rubber backing against caliper "cage" HTH :y
Logged
1972 Ferrari Dino, 1967 Triumph TR4A, Mondeo 2.0TDCi Estate, Jaguar XJ 5.0V8 Portfolio

tunnie

  • Get A Life!!
  • *****
  • Offline Offline
  • Gender: Male
  • Surrey
  • Posts: 37625
    • Zafira Tourer & BMW 435i
    • View Profile
Re: Front brake pad orientation
« Reply #4 on: 31 July 2010, 15:16:51 »
put a bit of copper slip around the edge of that pads, where it sits in the calliper, and again on the pad where the piston pushes the pads. stops them squeaking  :y
« Last Edit: 31 July 2010, 15:17:07 by tunnie »
Logged

amba

  • Omega Baron
  • *****
  • Offline Offline
  • Gender: Male
  • Medway towns
  • Posts: 4827
    • German V6
    • View Profile
Re: Front brake pad orientation
« Reply #5 on: 31 July 2010, 16:41:28 »
All done /sorted and jobs a good,n.Never noticed different faces of pads last time round so must have just been luck.
All copper greased up Tunnie so no nasty noises.
Other strange thing with new pads is the brake pad wear sensor little pegs would not fit into new pads howeevr hard I tried .wiggled about and then ended up snapping 1 in half so only 1 now connected but as no light and always replace pads at about 20k miles never really an issue.
Any body else had that problem with peg not refitting.?
Big thanks Weds for offer but bought them this morning while in Dartford so if I had seen your kind offer first I would have saved the detour from A2.thanks agin though.
Logged

Weds

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Chatham, Kent
  • Posts: 653
  • My other hobby
    • Mercedes E class 350 CDi
    • View Profile
Re: Front brake pad orientation
« Reply #6 on: 01 August 2010, 04:23:08 »
Quote
Big thanks Weds for offer but bought them this morning while in Dartford so if I had seen your kind offer first I would have saved the detour from A2.thanks agin though.

No problem :-)
Logged
Pages: [1]   Go Up
« previous next »
 

Page created in 0.022 seconds with 18 queries.