Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please play nicely.  No one wants to listen/read a keyboard warriors rants....

Pages: 1 2 [3]  All   Go Down

Author Topic: bodging a wiper stalk  (Read 7445 times)

0 Members and 2 Guests are viewing this topic.

BigAl

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Bromley, Kent
  • Posts: 965
    • '07 Forester
    • View Profile
Re: bodging a wiper stalk
« Reply #30 on: 22 November 2009, 14:54:48 »
No laughing, but I finally got round to swapping the stalks, everything work as before, including the lack of variable setting.
No matter what I set the wheel to the interval is ~7 seconds :-[
Any ideas ?
Logged

omegadti

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Glasgow
  • Posts: 178
    • omega dti
    • View Profile
Re: bodging a wiper stalk
« Reply #31 on: 22 November 2009, 19:45:50 »
have you swapped the wires on the mid plug - you will have a blk/wht and a blk/yel wire left over.  On the main plug to the stalk there is a terminal with a blk/wht and blk/yel wire.   Cut these wires and join to wires from the mid connect in series.   PM me your email and I'll send some photos.   I did mine last week and after a bit of trial and error I have variable intermittent.
Logged

BigAl

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Bromley, Kent
  • Posts: 965
    • '07 Forester
    • View Profile
Re: bodging a wiper stalk
« Reply #32 on: 22 November 2009, 20:22:28 »
PM sent
Logged

omegadti

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Glasgow
  • Posts: 178
    • omega dti
    • View Profile
Re: bodging a wiper stalk
« Reply #33 on: 22 November 2009, 20:40:25 »
pm replied to
Logged

omegadti

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Glasgow
  • Posts: 178
    • omega dti
    • View Profile
Re: bodging a wiper stalk
« Reply #34 on: 22 November 2009, 20:41:35 »
ps you might need to change the relay under the bonnet to one that responds to the delay time
Logged

BigAl

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Bromley, Kent
  • Posts: 965
    • '07 Forester
    • View Profile
Re: bodging a wiper stalk
« Reply #35 on: 26 November 2009, 22:39:56 »
Quote
pm replied to
Many thanks for the mail :y
Logged

BigAl

  • Senior Member
  • ****
  • Offline Offline
  • Gender: Male
  • Bromley, Kent
  • Posts: 965
    • '07 Forester
    • View Profile
Re: bodging a wiper stalk
« Reply #36 on: 26 November 2009, 22:55:01 »
Quote
have you swapped the wires on the mid plug - you will have a blk/wht and a blk/yel wire left over.  On the main plug to the stalk there is a terminal with a blk/wht and blk/yel wire.   Cut these wires and join to wires from the mid connect in series.   PM me your email and I'll send some photos.   I did mine last week and after a bit of trial and error I have variable intermittent.
Oops!, I have only cut one wire from the main plug and wired in the 2 from the stalk, will rectify on Saturday
Must pay more attention in future :-[
Logged

omegadti

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Glasgow
  • Posts: 178
    • omega dti
    • View Profile
Re: bodging a wiper stalk
« Reply #37 on: 27 November 2009, 19:15:41 »
if you cut one of the wires from the 2 going to the terminal on the switch block you then connect the blk/wht from the mid plug to one side and the blk/yel to the other - make sure you have the right relay under the bonnet and it should work.   I can't beleive I've lived without this mod for six years - thank you OOF
Logged
Pages: 1 2 [3]  All   Go Up
« previous next »
 

Page created in 0.011 seconds with 17 queries.