Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[furion]

Hello
I have just instaled a ncdr with CID and cdc3 into my Omega.
The system works fine,and when i plug in my tech2,I get contact with the ncdr and the cdc3 but not the cid.
I would like to calibrate the BC but I can`t get in.
any one that know what the problem is? this system is from a Astra G so i think that the settings in the BC is programed for that car,not my 3.0 Omega.

Hope someone know what to do.
Thanks

[furion]

I just what to add that my index code is 22,maybe that should be another number for the Omege???

[MaxV6]

i'm no expert, but it's my understanding that the astra and vectra units do not work in the omega....   the communication method being slightly different??   i could be wrong though......   (although i have a vague memory of someone saying you could swap some pins round somewhere.....   )


thus CID's for the omega being so hard to find and expensive....  coz they're rare, and in ever decreasing supply....

[Marks DTM Calib]

They do work (as that is what mine had).

There is a mode pin that has to be set (pin 1 from memory although could be 32?, needs a 0V (ground) connection) so if retro fitting this needs including. If its a replacement then something is wrong as the wiring should be correct.

The mode pin sets the programming mode 

[TheBoy]

As MDTM suggests, connect pin 1 to pin 32, else you won't be able to communicate with the unit.

Your TIS200/GlobalTIS will give you the correct code index to use. 3.2 is 74, 3.0 I think is 45 (from memory).

[furion]

Thanks for replying.
Should the conection between pin 1 and 32 be permanently attached or just a loop in between when programing?
if I remember right,pin 32 is empty in my grey plug.

[furion]

Allso my car is a 1996,I have replaced the yello(26) and the black(12) plug with a grey(32).
I tested the car with a MID from a 1998 and everything works fine. I haven't used my tech2 on this MID because everything was working as I should.i don't have xenon so the black/purple xenon levling thing is just blinded.this came up as an error.

[TheBoy]

Thanks for replying.
Should the conection between pin 1 and 32 be permanently attached or just a loop in between when programing?
if I remember right,pin 32 is empty in my grey plug.

Permement

[TheBoy]

Allso my car is a 1996,I have replaced the yello(26) and the black(12) plug with a grey(32).
I tested the car with a MID from a 1998 and everything works fine. I haven't used my tech2 on this MID because everything was working as I should.i don't have xenon so the black/purple xenon levling thing is just blinded.this came up as an error.

OK, look at TIS2000/GlobalTIS/Web2TIS to find correct CI for your engine/gearbox/lighting/soundsystem/wheels etc combination. I assume you have access to these tools, as Tech2 isn't that useful without these resources.

[furion]

when I bought the tech2,i got 2cd's one of them i believe had the writing TIS2000 on it.
I shall fix the pin32 to ground asap.

[TheBoy]

State the following, and I'll look up the CI for you

Engine:
Gearbox: (Auto/Manual)
HIDs fitted: (Yes/No)

[furion]

X30xe,ar35
HID? If you mean xenon,that I don't have.

[furion]

I allso have a Bose system,but the logo doesn't  show in the display.is this set in the ncdr unit?

[TheBoy]

X30xe,ar35
HID? If you mean xenon,that I don't have.

Fairly certain it should be 44 for that, but let me confirm first when I get out my laptop.

[TheBoy]

I allso have a Bose system,but the logo doesn't  show in the display.is this set in the ncdr unit?

That is a toggle that is presented when you do the programming.