Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to OOF

Pages: 1 [2]  All   Go Down

Author Topic: ABS PCB repair  (Read 3001 times)

0 Members and 1 Guest are viewing this topic.

valliant72

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • London
  • Posts: 140
    • View Profile
Re: ABS PCB repair
« Reply #15 on: 05 August 2010, 14:53:07 »
Managed to get my module off, took about an hour. Had the same symptoms as Mike_T. BBA Reman arranged to pick it up tomorrow, hopefully it will be sorted by next week. :)
Logged

Mike_T

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Trimley Nr Felixstowe
  • Posts: 66
    • View Profile
Re: ABS PCB repair
« Reply #16 on: 06 August 2010, 21:14:54 »
Hi, upon opening the unit to reveal the PCB it was found that there were wires as thin as 0.03mm / 0.001" wich were too easily broken whilst removing the "Sticky Gel" covering the board. Sadly the repair had to be abandoned.
Even with the skills and specialist equipment my company has at repairing "Normal" PCBs a repair on this was not going to be reliable.
General feeling was that if a setting (hard) resin had been used then the wires would not have been subjected to movement and eventual failure due to vibrations over time.
Searching the web I think this company seam to be good .......http://www.bba-reman.com/catalogue/DetailedProduct.aspx?DetailedProduct=782.
Logged

valliant72

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • London
  • Posts: 140
    • View Profile
Re: ABS PCB repair
« Reply #17 on: 11 August 2010, 11:46:19 »
Well got a call for BBA Reman saying my module is not repairable  :(. So now got to fiind another. Anyone got an abs module their looking to sell. Would post in wanted section but dont have enough posts. PS would a 2.6 module be ok. as only engine size different?
« Last Edit: 11 August 2010, 11:51:58 by valliant1 »
Logged

Kevin Wood

  • Global Moderator
  • *****
  • Offline Offline
  • Gender: Male
  • Alton, Hampshire
  • Posts: 36450
    • Jaguar XE 25t, Westfield
    • View Profile
Re: ABS PCB repair
« Reply #18 on: 11 August 2010, 15:06:03 »
Quote
Well got a call for BBA Reman saying my module is not repairable  :(. So now got to fiind another. Anyone got an abs module their looking to sell. Would post in wanted section but dont have enough posts. PS would a 2.6 module be ok. as only engine size different?

Engine ECU is very different on the 2.6 so the interface to the ABS ECU could be different. I wouldn't risk it unless the part numbers match. Even then, it might need reconfiguring with a tech 2. Better to find one from a 2.5/3.0 IMHO.

Kevin
Logged
Tech2 services currently available. See TheBoy's price list: http://theboy.omegaowners.com/

valliant72

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • London
  • Posts: 140
    • View Profile
Re: ABS PCB repair
« Reply #19 on: 11 August 2010, 15:12:43 »
Hi thanks for the Replies. Would a 3.0 module need reprogramming?
Logged

valliant72

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • London
  • Posts: 140
    • View Profile
Re: ABS PCB repair
« Reply #20 on: 12 August 2010, 18:01:23 »
On recieving back my module that BBA Reman said was unrepairable, i had a look inside under a usb microscope. None of the fine wires are broke, so there must be another reason for failure other than these wires as mentioned on this forum elsewhere. Just got to see if my replacement turns up.  :-/
Logged
Pages: 1 [2]  All   Go Up
« previous next »
 

Page created in 0.016 seconds with 17 queries.